IKEA VÅGDAL 704.636.00 Connection Cord instructions manual

The IKEA VÅGDAL 704.636.00 Connection Cord is a power supply accessory designed for use with compatible IKEA lighting products. It provides a safe and reliable electrical connection, featuring a standardized plug and socket design, appropriate voltage and current ratings for low-voltage lighting systems, and safety certifications. Below are key sections for safety, features, installation, specifications, operation, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Installation 4. Specifications 5. Connection Guide 6. Operation 7. Care & Maintenance 8. Regulatory Information 9. Troubleshooting

Features at a Glance

Key components: Insulated power cord with molded plug, standardized connector, strain relief, and safety markings.

Feature	Description
Connector Type	Standardized low-voltage plug for IKEA VÅGDAL system
Cable Length	As specified for intended application
Insulation	Double-insulated for user safety
Voltage Rating	Designed for low-voltage DC output
Current Rating	Rated for maximum load of connected device
Polarity	Keyed connector to ensure correct polarity
Strain Relief	Reinforced cable entry points
Safety Marks	CE, GS, or other applicable certifications
Compatibility	Designed for specific IKEA VÅGDAL products
Color	Standard black or white insulation

Safety Information

Read all instructions before installation and use.

Inspect cord before use: Check for cuts, frays, or damage to insulation.
Use only with compatible IKEA VÅGDAL products as specified.
Do not overload: Use only with intended voltage and current ratings.
Keep away from heat sources and sharp edges.
Do not modify or repair the cord. Replace if damaged.

WARNING! Risk of electric shock or fire if used improperly. Ensure power is disconnected before handling connections. Do not use with damaged cord or plug.

Installation

Ensure power is turned OFF at the mains before beginning installation.

Identify ports: Locate the DC output port on the power adapter and the input port on the VÅGDAL device.
Align connector: Match the keyed shape of the plug with the socket.
Connect: Push plug firmly into socket until it clicks or seats fully.
Route cable: Arrange cord safely to avoid pinching, tension, or tripping hazards.
Secure strain relief: Use provided clips or ties if included.
Power on: Only after all connections are secure, restore power at the mains.

CAUTION! Do not force connection. If plug does not fit, verify compatibility. Ensure connections are dry.

Specifications

Product Code: VÅGDAL 704.636.00
Type: Low-voltage DC connection cord
Dependent on connected power adapter (e.g., 12V DC)
Current Rating: [Specify max amperage, e.g., 2A]
Cable Length: [Specify length, e.g., 1.5 meters]
Connector: Barrel plug or proprietary IKEA connector
Polarity: Center-positive or as marked on plug
Insulation: PVC or equivalent
Operating Temperature: 0°C to 40°C
Safety Standards: Complies with relevant EU/low-voltage directives

Connection Guide

Connect only to approved IKEA VÅGDAL power adapters and devices.

Typical Setup: Wall outlet → IKEA Power Adapter → VÅGDAL Connection Cord → VÅGDAL Light/Lamp.

Step-by-step visual guide (text description):

Plug the power adapter into a wall outlet.
Insert the VÅGDAL connection cord plug into the output port of the power adapter.
Insert the other end of the cord into the input port on your VÅGDAL lamp or light fixture.
Switch on the lamp using its built-in switch or control.

Tip: Ensure all connections are tight and secure. A loose connection can cause intermittent operation or overheating.

Operation

Once installed, operation is controlled by the connected device (lamp switch, remote, etc.).

Power: Use the switch on the connected lamp or the main power switch.
Normal Use: The cord is designed for continuous operation within its rated specifications.
Disconnection: Always turn off power before disconnecting the cord from either end.

WARNING! Do not pull the cord to disconnect. Grasp the plug body. Do not coil cord tightly during use, as this may cause overheating.

Care & Maintenance

Unplug from mains power before any cleaning or inspection.

Cleaning: Wipe with a dry, soft cloth. Do not use liquids or abrasive cleaners.
Inspection: Periodically check for damage to insulation, plug, or connector.
Storage: If not in use, coil loosely and store in a cool, dry place.

CAUTION! Never immerse in water or other liquids. Do not expose to direct sunlight or high temperatures for prolonged periods.

Regulatory Information

This product complies with the essential requirements of the relevant European directives (e.g., Low Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU). It bears the CE mark. IKEA and VÅGDAL are trademarks of Inter IKEA Systems B.V. For more information, recycling instructions, or support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Device does not power on	Loose connection or no power	Check all connections are secure. Verify wall outlet has power. Ensure main switch on lamp is ON.
Intermittent operation	Damaged cord or poor connection	Inspect cord for damage. Ensure plug is fully inserted into both the adapter and the device.
Connector does not fit	Wrong cord or incompatible device	Verify product code (704.636.00) and compatibility with your IKEA VÅGDAL product.
Cord or plug feels warm	Overload or short circuit	Disconnect immediately. Check device power rating does not exceed cord rating. Inspect for damage.
Visible damage to cord	Physical wear or misuse	Stop using immediately. Do not attempt repair. Replace with a genuine IKEA VÅGDAL 704.636.00 connection cord.

Replacement: Use only identical IKEA spare part 704.636.00.

Support: Contact IKEA customer service or visit www.ikea.com for assistance and spare parts.