IKEA VIDJA 103.092.06 Floor Lamp instructions manual

The IKEA VIDJA 103.092.06 is a modern floor lamp featuring a tripod base, adjustable height, fabric shade, and an integrated on/off switch. It requires assembly and uses a standard E27 bulb (max 13W LED or equivalent, not included). Below are key sections for safety, parts list, assembly instructions, operation, care, and troubleshooting.

Parts Included

Check that all parts are present before starting assembly.

Note: Light bulb not included.

Safety Instructions

Read all instructions before assembly and use.

1. Electrical Safety: Use only with recommended bulb type (max 13W LED/E27). Do not exceed wattage.
2. Assembly: Ensure all parts are securely fastened. Do not use excessive force.
3. Placement: Place on stable, level surface away from heat sources and moisture.
4. Cord Management: Keep cord away from walkways to prevent tripping. Do not pinch or damage cord.
5. Children: Keep out of reach of young children during assembly and operation.

WARNING! Risk of electric shock. Unplug before assembly, cleaning, or bulb replacement.

Assembly Instructions

Estimated assembly time: 15-20 minutes. Tools provided.

1. Prepare Base: Lay tripod legs (A) flat. Attach feet caps if included.
2. Assemble Pole: Connect the three pole sections (B) by twisting clockwise until secure.
3. Attach Pole to Base: Insert bottom end of pole into center hole of tripod base. Tighten locking screw using provided Allen key.
4. Install Socket: Thread the cord through the center pole from top to bottom. Attach socket unit (D) to top of pole and secure.
5. Attach Shade: Slide fabric shade (C) over socket and attach to shade holder according to diagram. Ensure it sits evenly.
6. Final Check: Ensure all connections are tight and lamp stands upright without wobbling.

Tip: Two people may be helpful for steps 3 and 5.

Specifications

• Model: VIDJA 103.092.06
• Type: Floor Lamp, Tripod Design
• Height: Adjustable from 140cm to 160cm (55" to 63")
• Shade Material: Polyester fabric
• Base Material: Powder-coated steel
• Bulb Socket: E27 (standard)
• Max Wattage: 13W LED or equivalent (not to exceed)
• Cord Length: 180cm (71 inches)
• Switch Type: In-line cord switch
• Weight: 3.2 kg (7 lbs) assembled

Operation & Controls

Operation is simple once assembled.

1. Insert Bulb: Screw an E27 bulb (max 13W LED) into socket. Do not overtighten.
2. Power: Plug cord into standard 120V AC wall outlet.
3. Switch: Use the in-line switch on the cord to turn lamp ON/OFF.
4. Height Adjustment: Loosen the pole locking mechanism, adjust to desired height, and retighten.
5. Positioning: The tripod base allows for stable placement on most floor surfaces.

Note: Lamp may become warm during use. This is normal.

Bulb Replacement

Always unplug lamp before replacing bulb.

1. Allow bulb to cool completely if lamp was recently on.
2. Unplug lamp from wall outlet.
3. Gently unscrew old bulb counterclockwise.
4. Screw new E27 bulb (max 13W LED) clockwise until snug.
5. Plug lamp back in and test with switch.

CAUTION! Use only recommended bulb type to prevent overheating and damage.

Care & Cleaning

Regular care maintains appearance and safety.

• Unplug lamp before any cleaning.
• Shade: Use a soft brush or vacuum with soft brush attachment to remove dust. Do not wash.
• Metal Parts: Wipe with a soft, slightly damp cloth. Dry immediately. Do not use abrasive cleaners.
• Cord: Wipe with dry cloth. Check periodically for damage.

WARNING! Never immerse lamp, cord, or plug in water or other liquids.

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included with purchase or available at www.ikea.com.

Support: For missing parts, assembly help, or warranty claims, contact IKEA customer service at 1-888-888-4532 or visit your local IKEA store.

Troubleshooting

Disposal: Dispose of according to local regulations for electronic waste. Recycle where possible.

Service: For issues not resolved above, contact IKEA customer support.