IKEA VEDHAMN 205.003.70 Deco Strip instructions manual

The IKEA VEDHAMN 205.003.70 Deco Strip is a decorative LED lighting strip designed for ambient illumination. It features energy-efficient LED technology, a flexible design for easy mounting, adhesive backing for installation, a low-voltage power supply, and a simple plug-and-play setup. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Mounting & Positioning 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Flexible LED strip, Adhesive backing, Low-voltage power adapter, Connection cables, Mounting clips (if included).

Feature	Description
LED Strip	Flexible, energy-efficient lighting with consistent brightness
Adhesive Backing	Pre-applied tape for easy mounting on clean, dry surfaces
Power Adapter	Low-voltage DC power supply for safe operation
Connection Cables	For extending or connecting multiple strips (if applicable)
Mounting Clips	Optional clips for additional securing (model dependent)
Cut Marks	Designated points for customizing strip length (if supported)
Plug & Play	Simple connection to power adapter
Low Heat Emission	LEDs remain cool during operation
Dimmable	Compatible with external dimmers (check specifications)
Color Temperature	Warm white or cool white options (model dependent)

Installation

Unpack and inspect contents. Ensure surface is clean, dry, and smooth.

Plan layout: Determine desired mounting location and length.
Prepare surface: Clean with isopropyl alcohol and let dry completely.
Peel backing: Remove protective liner from adhesive backing.
Apply strip: Press firmly onto surface along planned path.
Connect power: Plug strip into power adapter, then adapter into wall outlet.

WARNING! Do not install near heat sources or in damp locations unless rated for such use. Ensure power is off during installation.

First-Time Setup

After installation, power on the strip to test.

Check connections: Ensure all connectors are fully seated.
Power on: Plug adapter into a 120V AC outlet.
Verify operation: LED strip should illuminate evenly.
Adjust positioning: If needed, reposition before adhesive sets fully (first few minutes).
Secure with clips: If included, add mounting clips for extra hold.

CAUTION! Do not stretch or bend the strip sharply (minimum bend radius as specified). Do not overlap LED strips.

Specifications

Model: VEDHAMN 205.003.70 Deco Strip.
Light Source: LED, non-replaceable.
Power Consumption: Low wattage (check label for exact value).
Input Voltage: 120V AC, 60Hz (via adapter).
Output Voltage: Low-voltage DC (e.g., 12V or 24V).
Length: Standard strip length (e.g., 2m/78.7 inches).
Color Temperature: As specified (e.g., 2700K Warm White).
Beam Angle: Wide angle for even illumination.
Lifespan: Up to 25,000 hours (typical).
Operating Temp: Standard indoor temperature range.

Controls and Settings

Basic on/off control via power adapter plug. No built-in controls on strip.

External Controls: Use with compatible wall switch, dimmer, or smart home controller (if supported).

Dimming: If dimmable, use compatible LED dimmer switch (TRIAC or PWM type as specified). Color Options: Fixed color temperature; not adjustable unless RGB model. Installation: Adhesive mounting only; optional clips for reinforcement. Safety: Overheat protection may be included in power adapter.

Connecting to Power

Only use provided IKEA power adapter. Do not modify or use other adapters.

Ensure strip and adapter are unplugged.
Connect strip cable to adapter output jack.
Plug adapter into 120V AC wall outlet.
Switch on power at outlet if controlled by switch.

Tip: Use a surge protector for added safety. Do not overload electrical circuits.

Mounting & Positioning

Designed for indoor use on suitable surfaces.

Surface types: Clean, dry, smooth surfaces like wood, metal, painted drywall.
Avoid: Textured, dusty, oily, or damp surfaces.
Bending: Bend gently along cut marks if shortening; do not bend over sharp edges.
Cutting: Cut only at marked cut points if length adjustment is needed.
Securing: For heavy strips or vertical mounting, use additional mounting clips.
Hiding wires: Use cable channels or conceal wires along trim.

WARNING! Do not mount in enclosed fixtures unless rated for such use. Ensure adequate ventilation.

Safety Features

Low-voltage operation for safety. Adapter includes short-circuit and overheat protection. LED strips generate minimal heat.

Care & Cleaning

Unplug power before cleaning. Use dry, soft cloth to dust. For stains, use slightly damp cloth; do not use chemicals or abrasives.

CAUTION! Do not immerse in water or other liquids. Do not use solvents.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © IKEA; trademarks of Inter IKEA Systems B.V. For support, visit www.ikea.com or contact IKEA customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Strip does not light up	Power connection	Check if adapter is plugged in; ensure outlet is live; verify strip is connected to adapter.
Partial lighting	Connection or damage	Check connections between strip segments; inspect for physical damage.
Dim or flickering light	Voltage/connection	Ensure adapter is correct rating; check for loose connections; try different outlet.
Adhesive not holding	Surface preparation	Clean surface thoroughly with alcohol; apply pressure for 30 seconds; use mounting clips.
Overheating adapter	Ventilation/overload	Ensure adapter has airflow; do not cover; check if strip length exceeds adapter capacity.

Reset: Unplug adapter for 30 seconds, then reconnect.

Service: Contact IKEA customer service; do not attempt to repair strip or adapter.