IKEA VATTUDALEN 891.581.72 Sink instructions manual

The IKEA VATTUDALEN 891.581.72 is a stainless steel single bowl kitchen sink designed for durable daily use. It features a standard single drain hole configuration, a brushed satin finish for scratch resistance, sound-absorbing undercoating to reduce noise, and is compatible with most standard kitchen faucets and accessories. Below are key sections for safety, features, installation, care, and warranty information.

1. Features at a Glance 2. Package Contents 3. Safety Information 4. Specifications 5. Installation Instructions 6. Connecting Plumbing 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Features at a Glance

Key components: Stainless steel bowl, pre-cut drain hole, sound-absorbing undercoating, brushed satin finish.

FeatureDescription
Material18-gauge stainless steel (AISI 304)
FinishBrushed satin (scratch-resistant)
Bowl ConfigurationSingle bowl, right drain
UndercoatingSound-absorbing pad to reduce noise
Dimensions (Overall)Approx. 33" x 22" (84 cm x 56 cm)
Bowl DepthApprox. 8" (20 cm)
Drain HoleStandard 3.5" (89 mm) diameter
Faucet HolesNone (deck mount required)
CompatibilityMost standard drain assemblies and faucets
WeightApprox. 25 lbs (11.3 kg)

Package Contents

Unpack and inspect all items before installation.

  1. IKEA VATTUDALEN sink (1 piece)
  2. Installation template (1 sheet)
  3. Mounting clips set (quantity varies)
  4. Instruction manual (this document)

NOTE: Drain assembly, faucet, and sealant are sold separately.

Safety Information

Read all instructions before beginning installation.

  1. Wear safety gloves when handling the sink to prevent cuts from sharp edges.
  2. Ensure countertop is level, clean, dry, and structurally sound to support the sink and weight.
  3. Turn off water supply and disconnect power to the kitchen area before installation.
  4. Use two people to lift and position the sink to avoid injury or damage.

WARNING! Improper installation can cause water damage, personal injury, or void warranty. If unsure, consult a professional plumber.

Specifications

Installation Instructions

Follow these steps for proper under-mount installation.

  1. Prepare Countertop: Ensure cutout matches template dimensions. Edges must be smooth and sealed if using wood or laminate.
  2. Dry Fit: Place sink into cutout without sealant to check fit. It should sit flush without rocking.
  3. Apply Sealant: Run a continuous bead of 100% silicone sealant along the top rim of the sink.
  4. Position Sink: Carefully lower sink into cutout. Press down firmly to ensure even sealant contact.
  5. Secure with Clips: From underneath, attach mounting clips to sink rim and tighten against countertop. Follow clip spacing per template.
  6. Clean Excess Sealant: Wipe away any squeezed-out sealant with a damp cloth before it cures.
  7. Curing Time: Allow sealant to cure fully (check product label, typically 24 hours) before connecting plumbing or using sink.

CAUTION! Do not overtighten clips as this can warp the sink. Ensure sealant is suitable for kitchen use and water contact.

Connecting Plumbing

Connect drain and water supply lines after sink is securely installed and sealant is cured.

  1. Install Drain Assembly: Apply plumber's putty or silicone gasket to drain flange. Insert into sink hole and tighten locknut from below.
  2. Connect P-Trap: Attach P-trap to drain tailpiece and wall drain pipe. Ensure all connections are hand-tightened, then use wrench for a final quarter-turn.
  3. Install Faucet: If using a deck-mount faucet, install it according to the faucet's manual before setting the sink, or access from above after sink is placed.
  4. Connect Water Lines: Attach supply lines to faucet valves and shut-off valves. Ensure lines are not kinked.
  5. Check for Leaks: Slowly turn on water supply. Check all connections for leaks. Tighten slightly if necessary.

Tip: Use a bucket under connections during initial water test to catch any drips.

Care & Maintenance

Proper care will maintain the sink's appearance and longevity.

CAUTION! Never use acidic cleaners (e.g., for lime scale) containing hydrochloric or phosphoric acid on stainless steel.

Troubleshooting

SymptomPossible CauseCorrective Action
Sink is rocking or looseUneven countertop; clips not tightened evenly; insufficient sealantCheck countertop level. Loosen all clips, re-center sink, and retighten clips evenly in a cross pattern.
Water pooling around sink edgesFailed sealant; gap between sink and countertopTurn off water, dry area completely. Remove old sealant and reapply a fresh, continuous bead of silicone.
Loud noise when water runsMissing or damaged sound-absorbing undercoatingMinimize impact noise by using a sink grid or mat. The undercoating cannot be replaced after installation.
Scratches on surfaceAbrasive cleaning tools or materialsMinor scratches in the brushed finish can often be lessened by rubbing gently along the grain with a non-abrasive pad.
Discoloration or rainbow effectMineral deposits from hard water; residue from certain foodsClean with a vinegar-water solution (50/50), rinse thoroughly, and dry. For persistent stains, use a dedicated stainless steel cleaner.

Warranty & Support

IKEA VATTUDALEN sinks come with a 25-year limited warranty against defects in material and workmanship under normal household use. The warranty does not cover damage from improper installation, accident, misuse, lack of maintenance, or commercial use.

For Support:
IKEA Customer Service: 1-888-888-4532
Website: www.ikea-usa.com
Visit your local IKEA store for parts (e.g., mounting clips) or further assistance.

Note: Retain your receipt as proof of purchase for warranty claims.

IKEA VATTUDALEN 891.581.72 Sink instructions manual © - All Rights Reserved 2025