IKEA VATTENSTEN 805.306.04 Light Strip instructions manual

The IKEA VATTENSTEN 805.306.04 is a flexible LED light strip designed for indoor use, offering customizable lighting solutions for various spaces. It features a low-voltage DC power supply, adhesive backing for easy mounting, and is compatible with IKEA's smart lighting ecosystem (if applicable). Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Flexible LED strip, Power Adapter, Connector Cables, Remote Control (if included), Mounting Clips/Adhesive Tape.

Installation

Unpack and inspect contents. Ensure surface is clean, dry, and smooth.

1. Plan Layout: Decide where to place the strip. It can be cut at marked points if needed.
2. Prepare Surface: Clean the mounting surface with isopropyl alcohol and let it dry completely.
3. Mount the Strip: Peel off adhesive backing and press the strip firmly onto the surface. Use mounting clips for additional support if provided.
4. Connect Power: Connect the strip to the power adapter using the provided connector. Ensure polarity is correct.
5. Plug In: Connect the power adapter to a standard 120V AC outlet.

WARNING! Do not install near heat sources or in damp/wet areas. Ensure all connections are secure before powering on.

First-Time Setup

Power on the light strip; follow these steps for initial configuration.

1. Power On: Plug in the power adapter. The strip should light up.
2. Remote Pairing (if applicable): Point the remote at the strip's receiver and press the power button. Follow any included pairing instructions.
3. Smart Setup (if applicable): For TRÅDFRI compatibility, use the IKEA Home Smart app to add the light strip to your network.
4. Test Functions: Use the remote or app to test on/off, dimming, and color changes.

CAUTION! Do not bend the strip sharply (minimum bend radius as specified). Do not overload the power supply by connecting too many extensions.

Specifications

• Model: VATTENSTEN 805.306.04
• Light Source: LED
• Length: [e.g., 2 meters / 78.7 inches] (total, may be cuttable)
• Power Consumption: [e.g., 10W]
• Input Voltage: 120V AC, 60Hz
• Output Voltage (Adapter): [e.g., 24V DC]
• Luminous Flux: [e.g., 800 lumens]
• Color Temperature: [e.g., 2700K (Warm White) or Adjustable]
• CRI (Color Rendering Index): >80
• Lifespan: Up to 25,000 hours
• Operating Temperature: 32°F to 104°F (0°C to 40°C)

Controls and Settings

Control via included remote, wall switch, or IKEA Home Smart app.

Remote Functions (typical): POWER ON/OFF, Brightness +/- (DIM), Color Selection (for RGB models), Mode (Static, Flash, Fade, Smooth).

App Controls (TRÅDFRI): On/Off, Dimming, Scheduling, Grouping with other lights, Scene setting.

Manual Settings: The strip itself has no buttons. All control is external via remote, switch, or smart system.

Connecting to Power & Controllers

Power Adapter: Connects to strip and wall outlet. Extensions: Use official IKEA connectors to join multiple strips.

1. Ensure the light strip and power are OFF.
2. Align the connector pins with the strip's copper pads (observe + and - markings).
3. Snap the connector into place securely.
4. Connect the other end of the cable to the power adapter or controller.
5. Plug the power adapter into the wall outlet.

Tip: Do not connect strips in series beyond the maximum length specified in the manual to avoid voltage drop and overheating.

Operation & Customization

Use the remote or app for daily operation.

1. Turning On/Off: Press the POWER button on the remote or use the app.
2. Adjusting Brightness: Press the DIM+ or DIM- buttons.
3. Changing Color (RGB models): Press the color buttons (e.g., RED, GREEN, BLUE, WHITE) or use the color wheel in the app.
4. Selecting Mode: Press the MODE button to cycle through static, dynamic, and effect modes.
5. Creating Schedules: In the IKEA Home Smart app, set timers for automatic on/off.

WARNING! Do not cover the light strip while in operation to prevent overheating. Ensure adequate ventilation.

Safety Information

Read all instructions before installation and use.

• For indoor use only. Not waterproof.
• Use only with the provided IKEA power adapter.
• Do not install in enclosed fixtures unless rated for such use.
• Disconnect power before making any connections or performing maintenance.
• Keep away from children and pets to avoid entanglement or chewing hazard.
• If the flexible cord is damaged, it must be replaced by the manufacturer or a qualified person.

Care & Cleaning

Unplug from power before cleaning.

1. Use a dry, soft cloth to gently wipe the surface of the LED strip.
2. For stubborn dirt, slightly dampen the cloth with water. Do not let moisture enter the connectors or electronics.
3. Never use abrasive cleaners, solvents, or chemicals.

CAUTION! Do not immerse in water or other liquids. Do not use compressed air to clean as it may damage the LEDs.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This product meets relevant safety standards for low-voltage lighting equipment. For EU market, it carries the CE mark. Copyright and design rights belong to Inter IKEA Systems B.V. For support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

Reset: For smart models, try resetting the light strip via the IKEA Home Smart app or by power cycling 6 times.

Service & Recycling: For defective products, return to IKEA store. Dispose of electronic waste according to local regulations.