IKEA VALLMORA 803.069.40 Wall Lamp instructions manual

The IKEA VALLMORA 803.069.40 is a wall-mounted lamp designed for indoor use, featuring a simple, modern design suitable for various room settings. It requires assembly and installation onto a wall, using the included mounting hardware. The lamp is intended for use with specific bulb types (not included). Below are key sections for safety, parts list, assembly, installation, operation, care, and troubleshooting.

1. Safety Information 2. Parts Included 3. Tools Required 4. Assembly Instructions 5. Wall Installation 6. Bulb Installation & Operation 7. Care & Maintenance 8. Specifications 9. Troubleshooting 10. Warranty & Support

Safety Information

Read all instructions before assembly and installation. Key safety warnings:

Warning	Description
Electrical Safety	Ensure power is turned OFF at the circuit breaker before installation. Do not install near water or in damp locations.
Bulb Specifications	Use only max [XX] Watt, [Bulb Type, e.g., E14] bulbs as specified. Exceeding wattage may cause fire.
Mounting Surface	Mount only on a solid wall that can support the lamp's weight. Do not mount on plasterboard alone without proper anchors.
Children	Keep packaging materials away from children. The lamp becomes hot during use; keep out of reach of young children.

WARNING! Failure to follow safety instructions may result in electric shock, fire, or injury.

Parts Included

Check that all parts are present before starting.

Lamp shade (1 pc)
Wall bracket / Mounting plate (1 pc)
Screws and wall plugs (set)
Instruction manual (this sheet)

Note: Light bulb(s) are not included. Electrical cord and plug are pre-attached to the lamp.

Tools Required

You will need the following tools (not included):

Drill with appropriate drill bit for wall plugs
Screwdriver (Phillips or as required by screws)
Pencil
Spirit level (recommended)
Tape measure

Assembly Instructions

Assemble the lamp before mounting it to the wall.

If the lamp shade is separate, attach it to the lamp body according to the diagram (usually by aligning and twisting).
Ensure all connections are secure but do not over-tighten.
Do not install the bulb until the lamp is securely mounted on the wall.

Tip: Lay out all parts on a clean, soft surface to avoid scratches.

Wall Installation

Follow these steps to mount the lamp on your wall.

Choose Location: Select a location near a power outlet. Ensure no electrical wires or pipes are behind the chosen spot.
Mark Holes: Hold the wall bracket against the wall. Use a pencil to mark the positions of the screw holes. Use a spirit level to ensure it is straight.
Drill Holes: Drill holes at the marked points using the correct drill bit size for the provided wall plugs.
Insert Plugs: Insert the wall plugs into the drilled holes.
Attach Bracket: Align the bracket with the holes and secure it to the wall using the provided screws.
Attach Lamp: Hang or secure the lamp assembly onto the mounted bracket as per the design (may involve sliding on or securing with a small screw).

CAUTION! If you are unsure about wall structure, consult a professional.

Bulb Installation & Operation

Installing the bulb and using the lamp.

Ensure the lamp is not plugged in.
Install the recommended bulb type (e.g., E14 max 40W LED) into the socket. Do not touch the bulb with bare hands if it is halogen.
Plug the cord into a standard wall outlet.
Use the switch on the cord or the wall switch to turn the lamp ON/OFF.

WARNING! The bulb and lamp shade will become hot during use. Allow to cool before touching or changing the bulb.

Care & Maintenance

Unplug the lamp before any cleaning or maintenance.

Cleaning: Wipe the lamp shade and body with a soft, dry cloth. Do not use abrasive cleaners or liquids.
Bulb Replacement: Allow the bulb to cool completely. Unscrew the old bulb and replace it with a new one of the same specification.
Inspection: Periodically check that the lamp is securely attached to the wall and that the cord is not damaged.

Specifications

Product Name: VALLMORA
Article Number: 803.069.40
Type: Wall Lamp
Recommended Bulb: 1 x Max [XX]W, [Socket Type, e.g., E14] (Bulb not included)
Voltage: 120V AC, 60Hz (for US/CA market)
Cord Length: Approximately [X] feet/meters
Material: [e.g., Steel/Plastic/Textile]
Color: As per product variant
Dimensions: Height: X", Width: Y", Depth: Z"

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not light up	Power/Bulb	Check if the outlet works. Ensure the bulb is screwed in properly and not burnt out.
Lamp flickers	Loose bulb or connection	Turn off, check bulb is tight. If using a dimmer switch, ensure bulb is dimmable.
Lamp feels loose on wall	Mounting screws	Tighten the screws securing the bracket to the wall. Ensure wall plugs are suitable for wall type.
Overheating	Bulb wattage too high	Immediately turn off and unplug. Replace with a bulb of the correct, lower wattage.

Warranty & Support

This IKEA product is guaranteed under the terms of the IKEA commercial warranty. For detailed warranty information, please visit www.ikea.com or contact your local IKEA store.

Customer Support: Visit IKEA website or call 1-888-888-4532 for assistance with assembly, missing parts, or product issues.

Recycling: Dispose of the product and its components according to local regulations for electronic/electrical waste.