IKEA VADHOLMA 003.743.44 Storage instructions manual

The IKEA VADHOLMA 003.743.44 is a versatile storage unit designed for living rooms, bedrooms, or home offices. It features a modular design with adjustable shelves, integrated cable management, soft-closing doors and drawers, and a sturdy construction suitable for various storage needs. Below are key sections for assembly, safety, features, installation, setup, maintenance, and troubleshooting.

Features at a Glance

Key components: Main frame, adjustable shelves, doors with soft-closing hinges, drawers with runners, back panel, cable management holes, and mounting hardware.

Package Contents & Tools Required

Unpack and verify all parts before starting assembly.

1. Package Contents: Main panels (sides, top, bottom), shelves, doors, drawers, back panel, hinges, drawer runners, screws, cam locks, dowels, wall attachment kit, assembly instructions.
2. Tools Required (not included): Phillips screwdriver, hammer, measuring tape, level, pencil.

IMPORTANT! Check for damage upon receipt. Contact IKEA if any parts are missing or defective.

Safety Instructions

Follow these instructions to ensure safe assembly and use.

1. Tip-Over Prevention: This furniture must be securely attached to the wall using the provided wall attachment device to prevent tipping, especially in homes with children.
2. Assembly Surface: Assemble on a soft, clean surface (e.g., carpet or blanket) to avoid scratching parts.
3. Lifting: The unit is heavy; use two people for lifting and moving.
4. Children: Keep children away during assembly. Do not let children climb on the unit.
5. Weight Distribution: Place heavier items on lower shelves. Do not exceed specified weight limits.

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure to wall.

Assembly Instructions

Assemble in the room where the unit will be used to avoid moving the fully assembled piece.

1. Prepare: Lay out all parts and hardware. Identify each part using the assembly guide illustrations.
2. Frame Assembly: Connect side panels to top and bottom panels using cam locks and dowels. Ensure all connections are tight and square.
3. Back Panel: Place the unit face down on a protected surface. Attach the back panel using provided screws to square and stabilize the frame.
4. Shelves: Insert adjustable shelves onto shelf pins at desired heights.
5. Doors & Drawers: Attach hinges to doors, then mount doors to frame. Assemble drawers and insert drawer runners into frame before sliding drawers in.
6. Final Check: Ensure all screws and cam locks are fully tightened. Check that doors and drawers open and close smoothly.

Tip: Do not fully tighten cam locks until the entire frame is assembled and squared.

Installation & Placement

Choose a suitable location and secure the unit to the wall.

1. Location: Place on a level, solid floor. Avoid direct sunlight, heat sources, or areas of high humidity.
2. Wall Attachment:
   • Locate wall studs using a stud finder.
   • Position the unit against the wall in its final location.
   • Use the provided wall attachment bracket. Screw one part to the back of the unit (top section) and the other part securely into wall studs.
   • Connect the bracket parts to secure the unit to the wall.
3. Leveling: Use a level to ensure the unit is not leaning. Adjust placement if necessary.

CAUTION! Never place the unit on uneven or unstable surfaces. Wall attachment is mandatory for safety.

Adjusting Shelves & Components

Customize the interior layout to suit your storage needs.

• Shelves: To adjust, lift shelf up and out of the shelf pins. Reposition pins to desired height (pre-drilled holes) and lower shelf onto new pins.
• Doors: Hinges allow for 3-way adjustment (height, depth, side-to-side) using a Phillips screwdriver to align doors perfectly.
• Drawers: To remove, open drawer fully, press down on the plastic levers on both sides of the runner inside the drawer, and pull drawer out. To reinsert, align and push in until it clicks.
• Cable Management: Route cables through designated holes in the back panel. Use adhesive cable clips (not included) for further organization.

Care & Maintenance

Proper care will maintain the appearance and longevity of your unit.

1. Cleaning: Wipe surfaces with a soft, damp cloth. Use a mild soap solution if needed. Dry immediately with a clean cloth.
2. Avoid: Do not use abrasive cleaners, scouring pads, or harsh chemicals (acetone, bleach).
3. Protection: Use coasters under glasses and placemats under hot items to prevent heat or moisture damage.
4. Hardware Check: Periodically check and tighten screws, especially cam locks and wall attachment hardware.

WARNING! Never soak the unit or allow liquids to pool on surfaces or enter joints.

Weight Limits & Specifications

• Overall Dimensions (W x H x D): Please refer to the product label or IKEA website for exact model dimensions.
• Material: Particleboard, Fiberboard, ABS plastic, Steel.
• Finish: White, Ash effect, or Black-Brown (varies by model).
• Max Shelf Load: 15 kg (33 lbs) per adjustable shelf.
• Max Drawer Load: 10 kg (22 lbs) per drawer.
• Total Unit Weight Capacity: Distributed load as per shelf limits. Heaviest items should be stored at the bottom.

Troubleshooting

Note: For persistent issues, consult the assembly guide illustrations or contact IKEA support.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for full terms and conditions.

• Support Website: www.ikea.com
• Assembly Guides & Manuals: Available for download on the product page.
• Spare Parts: Available through IKEA customer service.
• Contact: Visit your local IKEA store or use the contact options on the IKEA website.

Safety Notice: IKEA's top priority is safety. Always use wall attachment devices to prevent tip-over accidents.