IKEA UTRUSTA 094.727.07 Hinge instructions manual

The IKEA UTRUSTA 094.727.07 is a concealed hinge designed for mounting cabinet doors, featuring soft-closing functionality, adjustable height, depth, and side pressure, compatibility with various cabinet frames, and a load capacity suitable for standard cabinet doors. Below are key sections for safety, features, installation, adjustment, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Tools Required 4. Installation Steps 5. Hinge Adjustment 6. Specifications 7. Mounting Compatibility 8. Care & Maintenance 9. Warranty Information 10. Troubleshooting

Features at a Glance

Key components: Hinge cup, mounting plate, adjustment screws, soft-closing mechanism.

FeatureDescription
Soft-closingPrevents door from slamming shut
Height adjustmentVertical adjustment via screw
Depth adjustmentIn/out adjustment for door gap
Side pressure adjustmentLeft/right alignment of door
Concealed designHides inside cabinet when door is closed
Load capacityUp to 4 kg (8.8 lbs) per hinge
Opening angleUp to 110 degrees
MaterialSteel with nickel coating
Mounting plateFor attachment to cabinet frame
CompatibilityFits 35mm hinge cup holes

Package Contents

Unpack and inspect all components before installation.

  1. UTRUSTA hinge arm with cup (x2 per package)
  2. Mounting plate (x2 per package)
  3. Mounting screws for frame and door (x8)
  4. Plastic covers for screw heads (x4)
  5. Instruction manual

WARNING! Ensure all parts are present. Do not use if any component is damaged.

Tools Required

Gather necessary tools before beginning installation.

  1. Drill with 35mm Forstner bit or hinge boring bit
  2. Phillips screwdriver (#2)
  3. Measuring tape
  4. Pencil for marking
  5. Level (optional for alignment)

CAUTION! Use appropriate safety equipment when drilling.

Installation Steps

Follow these steps for proper hinge installation.

  1. Mark hinge positions: On door, mark center for 35mm cup hole (typically 21-23mm from door edge).
  2. Drill cup hole: Use 35mm bit to drill hole to depth of 12-13mm.
  3. Attach hinge to door: Insert hinge into cup hole, secure with provided screws.
  4. Mark frame positions: Align door to frame, mark positions for mounting plates.
  5. Attach mounting plates: Secure plates to cabinet frame using screws.
  6. Snap hinge onto plate: Align hinge arm with mounting plate and press until it clicks into place.
  7. Test movement: Open and close door to check alignment and soft-close function.

Tip: Install two hinges per door for standard sizes (top and bottom).

Hinge Adjustment

Fine-tune door position using adjustment screws.

Height adjustment (vertical): Turn screw at hinge arm base to move door up/down.

Depth adjustment (in/out): Turn screw on side of hinge to adjust door gap to frame.

Side pressure adjustment (left/right): Turn screw at mounting plate to align door horizontally.

Make small adjustments (1/4 turn at a time) and test door movement after each adjustment.

Specifications

Mounting Compatibility

Compatible with cabinet doors 12-25mm thick.

  1. Standard overlay doors (full overlay)
  2. Partial inset doors (check clearance)
  3. Frameless cabinet construction
  4. Face frame cabinets (with appropriate mounting)

Note: For inset doors, additional adjustments may be required.

Care & Maintenance

Clean with dry cloth only; avoid lubricants unless specified.

CAUTION! Do not use abrasive cleaners or solvents on hinge mechanism.

Warranty Information

IKEA limited warranty applies. For details, check IKEA warranty terms or contact customer service. Copyright © IKEA of Sweden. For support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

SymptomPossible CauseCorrective Action
Door doesn't close smoothlyMisalignmentAdjust height/depth/side pressure screws.
Soft-close not workingMechanism obstructedCheck for debris; ensure hinge is properly seated on plate.
Door sagsLoose screws or overloadTighten all screws; ensure weight is within 4kg per hinge limit.
Hinge doesn't snap onto plateMisaligned plateLoosen plate screws, realign, and retighten.
Door binds or sticksIncorrect cup hole depthVerify hole depth is 12-13mm; adjust if necessary.

Reset: Remove hinge from plate and reinstall if adjustments don't resolve issues.

Service: Contact IKEA customer service or visit www.ikea.com for replacement parts.

IKEA UTRUSTA 094.727.07 Hinge instructions manual © - All Rights Reserved 2025