IKEA UTRUSTA 092.739.15 Drawer Front instructions manual

The IKEA UTRUSTA 092.739.15 is a drawer front designed for compatibility with various IKEA drawer systems such as MAXIMERA and GODMORGON. It features a clean, modern design, pre-drilled holes for handles or knobs, and is made from durable, easy-to-clean materials. Below are key sections for overview, parts included, tools required, assembly instructions, mounting, adjustment, care, safety, and troubleshooting.

1. Product Overview 2. Parts Included 3. Tools Required 4. Assembly Instructions 5. Mounting to Drawer Runner System 6. Adjustment & Alignment 7. Care & Maintenance 8. Safety Information 9. Technical Specifications 10. Warranty & Support 11. Troubleshooting

Product Overview

Key features: Modern drawer front design, pre-drilled mounting holes, compatible with IKEA drawer systems, durable construction.

Feature	Description
Material	High-pressure laminate over particleboard
Color/Finish	White, matte finish
Dimensions (HxWxD)	15 cm x 60 cm x 2 cm (approx.)
Compatibility	MAXIMERA, GODMORGON, and other IKEA drawer systems
Pre-drilled Holes	Standard 96mm or 128mm hole spacing for handles
Weight Capacity	Designed for standard drawer loads when properly mounted
Surface	Easy to clean, scratch-resistant

Parts Included

Unpack and verify all parts before starting assembly.

Drawer Front Panel: 1 piece (UTRUSTA 092.739.15).
Mounting Brackets/Screws: Included with drawer runner system (not included with front alone).
Handle/Knob: Sold separately.
Instruction Manual: This document.

NOTE! Drawer runners, cabinet frame, and handles are purchased separately.

Tools Required

Gather these tools before beginning:

Phillips screwdriver (size #2).
Drill (optional, for pilot holes if not pre-drilled).
Measuring tape.
Level.
Pencil.

CAUTION! Use correct screwdriver size to avoid stripping screw heads.

Assembly Instructions

Follow these steps to attach handles and prepare the drawer front.

Attach Handle/Knob: Align handle with pre-drilled holes on drawer front. Insert screws from the back of the front panel and tighten securely with screwdriver.
Check Alignment: Ensure handle is straight and level before final tightening.
Prepare for Mounting: Identify top/bottom of drawer front (if applicable).

Tip: Do not overtighten screws to avoid damaging the material.

Mounting to Drawer Runner System

Mount the prepared front to the drawer box or runner system.

Position Drawer Box: Fully extend the drawer box from the cabinet.
Align Front Panel: Hold drawer front against drawer box, ensuring even gaps on all sides.
Secure Temporarily: Use provided screws to loosely attach front to drawer box through mounting brackets (usually 2-4 screws on each side).
Adjust for Gaps: Check gaps between drawer fronts and cabinet frame. Adjust position until even.
Final Tightening: Once aligned, fully tighten all screws.

WARNING! Ensure drawer is fully supported during mounting to prevent injury.

Adjustment & Alignment

Fine-tune the drawer front position for perfect fit.

Vertical Adjustment: Loosen screws slightly, move front up/down, retighten.
Horizontal Adjustment: Adjust left/right to ensure consistent side gaps.
Depth Alignment: Ensure front is flush with adjacent fronts or cabinet frame.
Check Operation: Open and close drawer multiple times to ensure smooth movement and no rubbing.

Note: Some IKEA runner systems have built-in adjustment mechanisms; consult runner manual if needed.

Care & Maintenance

To maintain appearance and function:

Cleaning: Wipe with damp cloth and mild detergent. Dry immediately.
Avoid: Abrasive cleaners, scouring pads, strong chemicals, or excessive moisture.
Inspection: Periodically check screw tightness and alignment.

CAUTION! Do not use steam cleaners or soak the drawer front.

Safety Information

Use only with compatible IKEA drawer systems rated for the intended load.
Ensure cabinet is securely anchored to wall to prevent tipping.
Do not exceed maximum weight capacity of drawer runners.
Keep children away from assembly area and small parts.
Check stability of drawer after installation.

WARNING! Heavy items should be placed at the back/bottom of drawer for stability.

Technical Specifications

Article Number: 092.739.15
Product Name: UTRUSTA
Type: Drawer Front
Material: Particleboard, High-pressure laminate
Color: White
Thickness: 2 cm
Edge Type: ABS edging
Country of Origin: See product label
Weight: Approx. 1.5 kg

Warranty & Support

IKEA limited warranty applies. For support:

Visit the IKEA store where purchased.
Contact IKEA Customer Service: 1-888-888-4532.
Online: www.ikea.com

Keep receipt as proof of purchase. Warranty does not cover damage from improper installation, misuse, or normal wear and tear.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Drawer front not aligned	Mounting screws loose or misaligned	Loosen screws, reposition front, ensure even gaps, retighten.
Drawer rubs or sticks	Front misaligned or overloaded	Realign front; check runner installation; reduce load.
Handle feels loose	Screws not tightened properly	Tighten screws from back of drawer front.
Gaps uneven	Drawer box not square or front mispositioned	Adjust drawer box within cabinet; use shims if necessary.
Front warped or damaged	Manufacturing defect or exposure to moisture	Contact IKEA for replacement if within warranty.

Note: For persistent issues, consult the manual for your specific drawer runner system.

Support: 1-888-888-4532; www.ikea.com