IKEA UPPVIND 704.882.95 Floor Lamp instructions manual

The IKEA UPPVIND 704.882.95 is a modern floor lamp featuring an adjustable head and arm for directional lighting, a sturdy weighted base for stability, an integrated on/off switch on the cord, and a fabric shade. It requires assembly and uses a max 13W E26/E27 LED bulb (not included). Below are key sections for safety, parts list, assembly instructions, operation, care, and troubleshooting.

1. Parts & Tools Included 2. Safety Instructions 3. Assembly Steps 4. Specifications 5. Operation & Adjustments 6. Bulb Replacement 7. Care & Cleaning 8. Troubleshooting 9. Warranty & Support

Parts & Tools Included

Before assembly, verify all parts are present. Key components: Base, Upright pole, Adjustable arm, Lamp head with socket, Fabric shade, Screws and hardware, Cord with switch.

Part Name	Quantity	Description
Weighted Base	1	Provides stability
Main Pole	1	Vertical support tube
Adjustable Arm	1	Horizontal arm with joints
Lamp Head	1	Holds bulb and shade
Fabric Shade	1	Diffuses light
Hardware Pack	1	Screws, washers, Allen key
Cord with Switch	1	Power cord with integrated on/off

Safety Instructions

Read all instructions before assembly and use.

Use only LED bulb max 13W E26/E27 base. Do not exceed wattage.
Ensure lamp is unplugged during assembly and bulb replacement.
Place on stable, level surface away from heat sources and water.
Do not use if cord or plug is damaged.
Keep out of reach of children during assembly.

WARNING! Risk of electric shock. Disconnect from power before any maintenance.

Assembly Steps

Estimated assembly time: 15-20 minutes. Follow steps in order.

Attach Base: Insert main pole into base hole. Secure with provided screw using Allen key.
Install Arm: Connect adjustable arm to top of pole. Tighten joint screw firmly but do not overtighten.
Attach Lamp Head: Screw lamp head onto end of arm. Ensure electrical connections inside are secure.
Install Shade: Place fabric shade over lamp head. It may clip or rest on a lip; ensure it is centered.
Route Cord: Run cord along arm and pole, using clips if provided. Plug into outlet.
Insert Bulb: Install appropriate LED bulb (not included). Do not touch bulb with bare hands.

CAUTION! Ensure all joints are tight to prevent lamp from collapsing. Use two people if needed.

Specifications

Model: UPPVIND 704.882.95
Type: Adjustable floor lamp
Max Bulb: 1 x 13W LED, E26/E27 base
Power Supply: 120V AC, 60Hz
Cord Length: Approx. 6 feet (1.8m)
Switch: In-line on cord
Material: Steel, plastic, fabric
Height Range: Adjustable from 50" to 60"
Weight: Approx. 8.8 lbs (4 kg)

Operation & Adjustments

Lamp features adjustable head and arm for directional lighting.

To Adjust: Gently move the arm and head to desired position. Joints are designed to hold position when released. Do not force beyond natural range.

To Operate: Use the on/off switch located on the power cord. Ensure lamp is plugged into a working outlet.

Tip: Position lamp so light falls where needed without shining directly into eyes.

Bulb Replacement

Use only LED bulb, max 13W, E26/E27 base.

Turn switch OFF and unplug lamp from outlet.
Allow existing bulb to cool completely if recently on.
Remove fabric shade (if necessary) by lifting off.
Unscrew old bulb counterclockwise.
Screw new bulb in clockwise until snug. Do not overtighten.
Replace shade and plug in lamp.

WARNING! Never use a bulb with higher wattage than specified. Risk of fire.

Care & Cleaning

Unplug lamp before cleaning.

Shade: Use a soft brush or vacuum with brush attachment to remove dust. Do not wash.
Metal/Plastic Parts: Wipe with a soft, dry cloth. For stubborn marks, use a slightly damp cloth. Dry immediately.
Cord: Wipe with dry cloth. Do not use chemicals or abrasives.

CAUTION! Do not immerse any part of the lamp in water or use liquid cleaners.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	No power / bad bulb	Check outlet; ensure plug is secure; replace bulb.
Lamp flickers	Loose bulb / faulty bulb	Turn off, unplug, and tighten bulb. Try a different bulb.
Lamp is unstable	Base not secure / uneven floor	Tighten base screw. Place on level surface.
Arm/head won't hold position	Joint screws loose	Tighten adjustment joint screws with Allen key.
Overheating	Wrong bulb wattage	Use only recommended 13W max LED bulb.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores.

For assembly help, missing parts, or product support:

Visit: www.ikea.com
Contact IKEA customer service: 1-888-888-4532
Have model number (704.882.95) and receipt ready.

Note: This manual is a guide. IKEA reserves the right to make changes.