IKEA UPPVIND 104.378.31 Floor Lamp instructions manual

The IKEA UPPVIND 104.378.31 is a modern floor lamp featuring a sleek metal frame, adjustable height, energy-efficient LED light source, touch-sensitive dimmer control, and a stable weighted base. Designed for home and office use, it provides ambient and task lighting. Below are key sections for safety, assembly, operation, care, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Safety Instructions 4. Assembly Instructions 5. Operation & Controls 6. Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Features at a Glance

Key components: Adjustable metal stand, weighted base, integrated LED panel, touch-sensitive dimmer control, and cable management.

Feature	Description
Adjustable Height	Extendable pole from 120cm to 150cm
Light Source	Integrated non-replaceable LED (3000K warm white)
Dimmer Control	Touch-sensitive with 3 brightness levels
Base	Weighted circular base for stability
Frame Material	Powder-coated steel
Power Input	AC 100-240V, 50/60Hz
Cable Length	1.8m power cord with plug
Switch Type	Integrated touch sensor on pole
Light Output	800 lumens (max)
Energy Class	A+

Package Contents

Unpack and verify all parts before assembly.

Main pole sections (3 pieces)
Weighted base (1 piece)
LED light head assembly (1 piece)
Set of screws and Allen key
Power cord with plug
Instruction manual (this document)

WARNING! Check for any damage during transport. Do not use damaged parts.

Safety Instructions

Read all instructions before assembly and use.

Use only with specified voltage (100-240V AC).
Do not disassemble the LED light source.
Keep away from water and humid environments.
Place on stable, level surface to prevent tipping.
Do not cover the lamp during operation.
Unplug before cleaning or maintenance.

CAUTION! Risk of electric shock if opened or modified. Not for outdoor use.

Assembly Instructions

Estimated assembly time: 15-20 minutes.

Attach Base: Insert bottom pole section into base hole. Secure with provided screw using Allen key.
Connect Pole Sections: Extend middle and top sections by twisting clockwise until locked.
Attach Light Head: Place LED assembly on top pole. Secure with locking ring (hand-tighten).
Cable Management: Route power cord through pole channels and out base opening.
Final Check: Ensure all connections are tight and lamp stands upright without wobbling.

Tip: Assemble on a soft surface to avoid scratching the finish.

Operation & Controls

Touch-sensitive control located on the pole, approximately 1m from base.

Turning On/Off: Single brief touch to the sensor area.

Dimming: Touch and hold (2 seconds) to cycle through 3 brightness levels (Low/Medium/High).

Adjusting Height: Loosen pole locking mechanism, adjust to desired height (120-150cm), retighten.

Power Saving: Lamp automatically enters standby after 30 minutes of inactivity (if enabled via setup).

Specifications

Model: UPPVIND 104.378.31
Dimensions (H): 120-150cm adjustable
Base Diameter: 30cm
Weight: 4.2kg
Light Source: Integrated LED, 15W
Color Temperature: 3000K (Warm White)
Luminous Flux: 800 lm (max)
CRI: >80
Lifespan: 25,000 hours
Input Voltage: 100-240V AC, 50/60Hz
Certifications: CE, RoHS, Energy Class A+

Care & Maintenance

Unplug lamp before cleaning.

Use dry, soft cloth to wipe metal surfaces.
For stubborn marks, use damp cloth with mild detergent. Dry immediately.
Do not use abrasive cleaners or solvents.
Check pole connections periodically for tightness.

CAUTION! Never immerse in water. Do not spray cleaning agents directly onto surfaces.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	No power/touch sensor issue	Check power outlet; ensure plug is connected; clean touch sensor area.
Light flickers	Loose connection/power issue	Check all pole connections; try different outlet.
Dimming not working	Sensor malfunction	Unplug for 1 minute, then retry; ensure touch is held for 2+ seconds.
Lamp wobbles	Uneven surface/loose base	Place on level surface; tighten base screw.
LED color changes	End of life indicator	Contact IKEA support for assessment (integrated LED).

Reset: Unplug for 30 seconds to reset electronic controls.

Warranty & Support

IKEA limited warranty: 5 years for LED light source, 2 years for other parts from date of purchase. Proof of purchase required.

For assistance: Visit IKEA store, contact IKEA customer support at 1-888-888-4532, or visit www.ikea.com.

Recycling: Dispose of according to local electronic waste regulations. Do not dispose with household waste.