IKEA TÄLLBYN 904.377.52 Floor Lamp instructions manual

The IKEA TÄLLBYN 904.377.52 is a modern floor lamp featuring a sleek metal frame, adjustable head for directional lighting, integrated on/off foot switch, and uses a max 13W E26/E27 LED bulb (not included). Designed for easy home assembly with included tools and parts. Below are key sections for safety, parts list, assembly instructions, operation, care, and troubleshooting.

1. Parts & Tools Included 2. Safety Instructions 3. Assembly Steps 4. Specifications 5. Operation & Controls 6. Bulb Replacement 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Parts & Tools Included

Before assembly, check all parts are present and undamaged.

Part Number	Description	Quantity
1	Base plate	1
2	Main pole section	1
3	Upper pole section	1
4	Lamp head with socket	1
5	Adjustment knob	1
6	Foot switch assembly	1
7	Hex key (Allen wrench)	1
8	Screws and fasteners	1 set

Safety Instructions

Read all instructions before assembly and use.

Electrical Safety: Use only with 120V AC, 60Hz. Ensure power cord is not pinched or damaged.
Bulb Specification: Use only E26/E27 base LED bulb, max 13W. Do not exceed wattage.
Placement: Place on stable, level floor away from high traffic areas, heat sources, and water.
Assembly: Assemble on a soft surface to avoid scratching. Ensure all connections are tight.

WARNING! Risk of electric shock. Unplug lamp before assembly, bulb replacement, or cleaning.

Assembly Steps

Estimated assembly time: 15-20 minutes.

Attach Base: Place base plate (1) on floor. Insert main pole (2) into base and secure with provided screw using hex key.
Connect Upper Pole: Slide upper pole (3) onto main pole, aligning holes. Insert and tighten adjustment knob (5) to desired height.
Attach Lamp Head: Connect lamp head (4) to top of upper pole. Ensure wires feed through pole. Secure with provided fastener.
Install Foot Switch: Plug foot switch assembly (6) into socket at base of pole. Route cord neatly along pole channel if applicable.
Final Check: Ensure all screws are tight. Gently wobble lamp to check stability. Plug into wall outlet.

Tip: Do not overtighten screws to avoid stripping threads.

Specifications

Model: TÄLLBYN 904.377.52
Type: Adjustable floor lamp
Material: Steel, powder-coated finish
Height: Adjustable from 48" to 60"
Bulb: 1 x E26/E27 base, max 13W LED (not included)
Switch: Integrated foot pedal (On/Off)
Cord Length: 6 ft (1.8 m)
Voltage: 120V AC, 60Hz
Weight: 8.8 lbs (4 kg) assembled

Operation & Controls

Power: Plug into standard wall outlet. Ensure outlet is not controlled by a wall switch unless desired.

Foot Switch: Press once to turn lamp on. Press again to turn off. The switch is located at the base for easy access.

Adjustment: - Height: Loosen adjustment knob, slide pole to desired height, retighten knob. - Direction: The lamp head pivots. Gently tilt head to direct light where needed.

Note: The lamp is designed for ambient or task lighting. Avoid forcing adjustments beyond their natural stop points.

Bulb Replacement

Unplug Lamp: Always disconnect from power before replacing bulb.
Cool Down: Allow old bulb to cool completely if it was recently on.
Access Socket: The socket is housed within the lamp head. You may need to gently tilt the head for better access.
Replace: Unscrew old bulb counterclockwise. Screw in new E26/E27 LED bulb (max 13W) clockwise until snug. Do not overtighten.
Test: Plug lamp back in and use foot switch to test.

CAUTION! Use only recommended bulb type and wattage to prevent overheating and damage.

Care & Maintenance

Cleaning: Unplug lamp. Wipe with a soft, dry cloth. For stubborn marks, use a slightly damp cloth and dry immediately.

DO NOT: Use abrasive cleaners, solvents, or spray liquids directly on the lamp. Do not immerse any part in water.

Storage: If disassembling for storage, keep all parts and fasteners together in the original packaging if possible.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	No power / Faulty bulb	Check wall outlet with another device. Ensure lamp is plugged in. Replace bulb.
Lamp flickers	Loose bulb / Poor connection	Turn off and unplug. Ensure bulb is screwed in tightly. Check cord for damage.
Lamp is unstable	Loose assembly / Uneven floor	Unplug. Tighten all screws and adjustment knob. Place on level surface.
Foot switch feels stuck	Debris in mechanism	Unplug. Gently clean around switch with a dry brush. Do not use lubricants.
Head does not stay in position	Pivot joint is loose	Check for a tension screw on the head joint. If accessible, tighten slightly.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for full terms.

For Assembly Help or Parts: Visit the IKEA website (www.ikea.com) and use your product number (904.377.52) to find assembly guides, spare parts, or contact customer support.

Recycling: At end of life, do not dispose of with household waste. Recycle according to local regulations for electronic equipment.