IKEA TVÄLLEN 094.408.77 Sink instructions manual

The IKEA TVÄLLEN 094.408.77 is a stainless steel single-bowl kitchen sink designed for durability and easy cleaning. It features a standard single drain hole configuration, a brushed satin finish to resist fingerprints and water spots, and is compatible with most standard kitchen faucets and accessories. Below are key sections for safety, features, installation, care, and warranty information.

1. Product Overview & Features 2. Package Contents & Tools Required 3. Safety Instructions 4. Installation Steps 5. Connecting Plumbing 6. Sealing & Waterproofing 7. Care & Maintenance 8. Troubleshooting 9. Specifications 10. Warranty & Support

Product Overview & Features

Key components: Stainless steel sink bowl, pre-cut template, mounting clips, and instructions.

Feature	Description
Material	18-gauge stainless steel, brushed satin finish
Bowl Configuration	Single bowl, right-hand drain
Dimensions (Overall)	Approx. 33" x 22" (varies by model)
Bowl Depth	Standard 8-inch depth
Drain Hole	Standard 3.5" diameter, center location
Mounting Type	Undermount or top-mount (check model)
Sound Dampening	Undercoating to reduce noise
Compatibility	Fits most standard 33" base cabinets
Finish	Resists fingerprints, easy to clean
Accessories Included	Mounting clips, template (if applicable)

Package Contents & Tools Required

Unpack and verify all parts before starting installation.

Package Contents: Sink bowl, mounting clips (quantity varies), installation template, instruction manual.
Tools You Will Need: Tape measure, pencil, jigsaw or hole saw, screwdriver, silicone sealant (100% silicone, waterproof), caulking gun, wrench set, safety glasses, work gloves.
Additional Materials (not included): Drain assembly, faucet, water supply lines, plumber's putty or silicone gasket.

WARNING! Wear safety glasses and gloves when cutting countertop. Ensure work area is well-ventilated when using sealant.

Safety Instructions

Read all instructions before beginning installation.

Turn off water supply and disconnect power to the kitchen area if necessary.
Use proper lifting techniques; sink is heavy and edges can be sharp.
Ensure countertop is clean, dry, and structurally sound before installation.
Follow local plumbing and building codes.
Keep children and pets away from the work area.

CAUTION! Stainless steel edges can be sharp. Handle with care to avoid cuts.

Installation Steps

Follow these steps for a secure and leak-free installation.

Prepare the Countertop: Place the provided template on the countertop. Ensure it is centered over the cabinet and aligned correctly. Trace the outline with a pencil.
Cut the Opening: Using a jigsaw with a fine-tooth blade, carefully cut along the traced line. Support the cutout section to prevent it from falling.
Test Fit: Place the sink into the cutout from above (for top-mount) or below (for undermount). Ensure it fits snugly and is level.
Attach Mounting Clips (Top-Mount): For top-mount sinks, attach the mounting clips to the underside of the sink rim according to the diagram. Position the sink in the cutout and tighten the clips from below to secure it to the countertop.
Undermount Installation: For undermount sinks, apply a bead of silicone adhesive to the sink rim. Lift the sink into place from below and secure it with brackets or clips according to the instructions. Support the sink until the adhesive sets.

Tip: Have a helper assist with holding the sink during installation to ensure proper alignment.

Connecting Plumbing

Install the drain and faucet after the sink is securely mounted.

Install the Drain Assembly: Apply plumber's putty or a silicone gasket to the underside of the drain flange. Insert the flange into the drain hole from the top. From below, attach the rubber gasket, friction ring, and locknut. Tighten securely.
Connect the P-Trap: Attach the tailpiece to the drain assembly. Connect the P-trap to the tailpiece and the wall drain pipe. Ensure all connections are hand-tightened, then use a wrench for a final quarter-turn. Do not overtighten.
Install the Faucet: Insert the faucet through the pre-drilled hole in the sink or countertop. From below, attach the mounting nuts and water supply lines. Connect the supply lines to the hot and cold water shut-off valves.
Check for Leaks: Slowly turn on the water supply. Check all connections (drain, P-trap, faucet supply lines) for any leaks. Tighten connections slightly if necessary.

WARNING! Ensure all plumbing connections are secure to prevent water damage. Test for leaks thoroughly.

Sealing & Waterproofing

Proper sealing is critical to prevent water damage to the cabinet below.

Top-Mount Sinks: Run a continuous bead of 100% silicone sealant along the underside of the sink rim before placing it into the cutout. After securing with clips, apply another bead of sealant along the joint between the sink rim and the countertop. Smooth with a wet finger.
Undermount Sinks: The primary seal is the adhesive bead applied during mounting. After the sink is secured, you may apply a bead of sealant along the interior seam where the sink meets the countertop for added protection.
Cure Time: Allow the silicone sealant to cure fully (refer to product label, typically 24 hours) before using the sink or getting the area wet.

CAUTION! Use only 100% silicone sealant. Do not use acrylic or latex caulk as it is not waterproof.

Care & Maintenance

To maintain the appearance and longevity of your stainless steel sink.

Daily Cleaning: Rinse with warm water and mild dish soap. Wipe dry with a soft cloth to prevent water spots.
Stain Removal: For minor stains or lime scale, use a paste of baking soda and water. Gently scrub with a soft cloth or non-abrasive sponge.
Scratch Prevention: Avoid using steel wool, abrasive cleaners, or harsh chemicals. Do not cut food directly on the sink surface.
To Restore Shine: Use a dedicated stainless steel cleaner or a mild vinegar solution. Always wipe in the direction of the grain (brushed finish lines).

Tip: Placing a mat or rack in the bottom of the sink can help prevent scratches from pots and pans.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Water pooling under sink	Leaking seal or plumbing connection	Check and re-tighten drain connections. Reapply silicone sealant around sink rim if cracked or missing.
Sink is loose or moves	Mounting clips not tightened properly	From under the counter, tighten all mounting clips securely. For undermount, check adhesive/bracket security.
Slow drainage	Clog in drain or P-trap	Remove P-trap and clean out debris. Use a drain snake if necessary. Avoid pouring grease down drain.
Scratches on surface	Abrasive cleaning tools	Use only recommended cleaners and soft cloths. Minor scratches may blend with the grain over time.
Water spots or discoloration	Hard water or not drying after use	Clean with vinegar solution. Get in the habit of wiping the sink dry after each use.

Specifications

Model Number: TVÄLLEN 094.408.77
Material: 18-gauge Stainless Steel (AISI 304)
Finish: Brushed Satin
Overall Dimensions (L x W): Approx. 33" x 22" (84 cm x 56 cm)
Bowl Dimensions (L x W x D): Approx. 31" x 18" x 8" (79 cm x 46 cm x 20 cm)
Weight: Approx. 25 lbs (11.3 kg)
Drain Hole Size: Standard 3.5" (89 mm)
Mounting Type: Top-mount (check specific model variant)
Warranty: Limited warranty - see documentation.

Warranty & Support

IKEA TVÄLLEN sinks come with a limited warranty. Please retain your receipt as proof of purchase.

Warranty Coverage: Covers defects in material and workmanship under normal household use for a specified period from date of purchase. Does not cover damage from improper installation, accident, misuse, or lack of maintenance.

For Support:
Visit the IKEA website: www.ikea.com
Contact IKEA Customer Support: 1-800-434-IKEA (4532)
Visit your local IKEA store for assistance with parts or installation questions.

Note: Installation services may be available for purchase separately through IKEA.