IKEA TVÄRHAND 005.184.13 Table Lamp instructions manual

The IKEA TVÄRHAND 005.184.13 is a modern table lamp designed for home or office use, featuring a stable base, adjustable shade, energy-efficient bulb compatibility (max 13W E14 LED), on/off switch, and a 1.8-meter power cord. Below are key sections for safety, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Lamp base, adjustable shade, bulb socket (E14), on/off switch, power cord with plug.

Package Contents

Unpack and verify all parts are present.

1. Lamp base (1 piece)
2. Adjustable shade (1 piece)
3. Bulb socket with pre-attached wires (1 set)
4. Power cord with plug (1 piece)
5. Assembly screws (2 pieces)
6. Instruction manual (this document)

WARNING! Check for damage before assembly. Do not use if any part is broken.

Assembly Instructions

Follow steps in order. Ensure lamp is unplugged during assembly.

1. Attach base: Place base on flat surface.
2. Connect socket: Insert bulb socket into base opening, secure with provided screw.
3. Attach shade: Slide shade onto socket neck, tighten adjustment knob.
4. Route cord: Thread power cord through base channel, connect wires to socket terminals (L to brown, N to blue).
5. Secure cord: Use cord clip on base to prevent pulling.
6. Insert bulb: Screw in compatible E14 LED bulb (max 13W).

CAUTION! Ensure all connections are tight. Do not overtighten screws.

Specifications

• Model: TVÄRHAND 005.184.13
• Bulb Type: E14 socket
• Max Wattage: 13W LED (equivalent to 60W incandescent)
• Voltage: 220-240V AC, 50/60Hz (check local rating)
• Cord Length: 1.8 meters
• Dimensions (H×W×D): 40 cm × 18 cm × 18 cm
• Weight: 1.2 kg
• Color: Black/White (as per variant)
• Material: Steel, plastic

Controls and Operation

Switch located on base or inline on cord. Shade adjustable by hand.

Operation: Plug into wall outlet. Press switch to turn on/off. Adjust shade angle by gently tilting.

Note: Lamp may become warm during use; this is normal. Allow to cool before handling shade.

Bulb Replacement

Ensure lamp is unplugged and bulb is cool.

1. Unplug lamp from outlet.
2. Allow bulb to cool if recently used.
3. Grip bulb firmly, turn counterclockwise to remove.
4. Insert new E14 LED bulb (max 13W), turn clockwise until snug.
5. Plug in and test.

WARNING! Use only recommended bulb type. Exceeding wattage may cause overheating.

Safety Information

Read all instructions before use.

• Use only with compatible E14 LED bulbs, max 13W.
• Do not use in bathrooms or other high-moisture areas unless rated.
• Keep away from children; small parts may pose choking hazard.
• Do not cover lamp or place near flammable materials.
• Inspect cord regularly for damage; do not use if damaged.
• This lamp is for indoor use only.

Care & Cleaning

Unplug and allow to cool before cleaning.

1. Use dry, soft cloth to wipe base and shade.
2. For stubborn marks, use damp cloth with mild detergent, then dry thoroughly.
3. Do not immerse in water or use abrasive cleaners.

CAUTION! Never spray liquids directly onto lamp. Avoid contact with electrical parts.

Warranty Information

IKEA limited warranty applies as per local regulations. Retain receipt as proof of purchase. Warranty covers defects in material and workmanship under normal use. Not covered: damage from misuse, improper installation, or unauthorized modification. For warranty claims, contact IKEA customer service with model number and receipt.

Troubleshooting

Service: For assistance, contact IKEA customer support or visit www.ikea.com.