IKEA TROTTEN 004.747.63 Storage Unit instructions manual

The IKEA TROTTEN 004.747.63 is a versatile, height-adjustable storage unit designed for office or home use, featuring a sturdy metal frame, adjustable shelves, and a clean, modern design. It is part of the TROTTEN series, known for its flexibility and durability. Below are key sections covering safety, assembly, installation, adjustment, care, and troubleshooting.

Product Overview & Contents

Key components: Metal frame, adjustable shelves, shelf supports, screws, cam locks, and assembly tools (if included).

Safety Information

Read all instructions before assembly. Ensure a safe workspace.

1. Work Area: Assemble on a clean, flat, protected surface to avoid scratches.
2. Lifting: The unit is heavy; use two people for lifting and assembly.
3. Stability: To prevent tipping, especially in homes with children, secure the unit to the wall using the provided anti-tip device.
4. Weight Limit: Do not exceed the maximum load per shelf as specified in the manual.
5. Tools: Use correct tools; avoid over-tightening screws.

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using the provided restraint device.

Tools Required

Tools you may need (some may be included):

• Hex key (Allen wrench) – usually provided.
• Phillips screwdriver.
• Hammer (for tapping pegs if needed).
• Level (for ensuring unit is straight after assembly).
• Pencil (for marking wall attachment points).
• Drill (for wall mounting, if required).

Tip: Check the contents against the parts list before starting. Contact IKEA if any parts are missing.

Assembly Instructions

Follow steps in order. Do not fully tighten all screws until the frame is squared.

1. Prepare Parts: Lay out all parts and hardware. Identify components using the manual illustrations.
2. Assemble Frame: Connect the vertical uprights using the provided crossbeams and cam locks. Hand-tighten screws.
3. Add Stabilizer: Attach any rear or side stabilizer bars for rigidity.
4. Install Shelf Supports: Insert the shelf support pegs into the desired holes on the uprights. Ensure they are fully seated and level on both sides.
5. Place Shelves: Carefully lift each shelf and lower it onto the support pegs. Ensure it is centered and secure.
6. Final Tightening: Once the frame is square and shelves are in place, go back and fully tighten all cam locks and screws.
7. Attach Feet/Glides: Screw the adjustable foot pads into the bottom of the uprights.

CAUTION! Do not stand on the shelves or use them as a ladder. The unit is not designed to support a person's weight.

Height Adjustment

The TROTTEN unit allows shelf height customization.

1. Empty Shelves: Remove all items from the shelf you wish to adjust.
2. Lift Shelf: Carefully lift the shelf up and off the support pegs.
3. Reposition Supports: Remove the support pegs and insert them into the new desired pre-drilled holes on the uprights. Ensure both sides are at the same height.
4. Replace Shelf: Lower the shelf back onto the new peg positions. Gently test for stability.

Note: Adjust shelves before loading them with heavy items for easier handling.

Installation & Placement

Proper placement ensures safety and longevity.

1. Choose Location: Select a firm, level floor surface away from direct heat sources or excessive humidity.
2. Level the Unit: Use a level on the top shelf. Adjust the foot pads by twisting them in or out until the unit is perfectly level. This prevents wobbling.
3. Wall Attachment (CRITICAL):
   • Locate the wall attachment bracket and screws.
   • Position the unit in its final location against the wall.
   • Mark the screw holes on the wall through the bracket.
   • Move the unit aside. Drill pilot holes into wall studs if possible.
   • Attach the bracket securely to the wall.
   • Move the unit back and secure it to the bracket using the provided screws.

Tip: For concrete or brick walls, use appropriate wall plugs (anchors) not included with the product.

Care & Maintenance

Clean regularly to maintain appearance.

• Metal Frame: Wipe with a soft, damp cloth. Dry immediately. Do not use abrasive cleaners or scouring pads.
• Shelves: For laminate shelves, use a mild soap solution. Avoid excessive water.
• Inspection: Periodically check that all screws and connections are tight. Re-tighten if necessary.
• Moving: Always empty the unit completely before attempting to move it. Lift, do not drag.

CAUTION! Do not use harsh chemicals, ammonia, or silicone-based sprays as they may damage the finish.

Specifications

• Article Number: 004.747.63
• Series: TROTTEN
• Color: White/Stained oak effect (or as per variant)
• Material: Frame: Steel, Epoxy/polyester powder coating. Shelves: Particleboard, Paper foil, Plastic edging.
• Dimensions (approx.): Height: Adjustable range (e.g., 120-160cm). Width: 80cm. Depth: 40cm.
• Max Load per Shelf: Refer to label on the unit or manual (typically 15-25 kg).
• Weight of Unit: Approximately 30 kg (varies).
• Packaging: Flat-pack.

Warranty & Support

IKEA limited warranty applies. See IKEA warranty terms for details.

Missing Parts or Need Help?

• Online: Visit IKEA website for assembly instructions, spare parts, or contact: www.ikea.com.
• Phone: Contact your local IKEA customer support center.
• In Store: Bring your receipt and article number to the Returns & Exchanges desk.

Note: Keep your receipt as proof of purchase for warranty claims.

Troubleshooting

Safety Reminder: If the unit remains unstable after troubleshooting, do not use it. Disassemble and check assembly steps or contact IKEA for support.

Service & Support: www.ikea.com or your local IKEA store.