IKEA TARVA 803.607.05 Drawer instructions manual

The IKEA TARVA 803.607.05 is a wooden drawer unit designed for the TARVA bed frame, featuring solid pine construction, simple Scandinavian design, and easy assembly. This manual provides essential information for unpacking, assembling, installing, and maintaining your TARVA drawer. Below are key sections covering safety, parts identification, step-by-step assembly, installation into the bed frame, care instructions, and troubleshooting.

1. Parts & Components 2. Tools Required 3. Safety Instructions 4. Step-by-Step Assembly 5. Installation into Bed Frame 6. Adjustments & Leveling 7. Care & Maintenance 8. Specifications 9. Warranty Information 10. Troubleshooting

Parts & Components

Key components included in the package: Drawer front panel, drawer sides, drawer back panel, drawer bottom panel, metal drawer runners, screws, cam locks, dowels, and assembly instructions.

Part Name	Description	Quantity
Drawer front panel	Solid pine front piece with pre-drilled holes	1
Drawer side panels	Left and right pine side pieces	2
Drawer back panel	Pine back piece for structural support	1
Drawer bottom panel	Fiberboard panel that slides into grooves	1
Metal drawer runners	Slide mechanism for smooth operation	2 sets
Assembly screws	Various sizes for connecting parts	1 packet
Cam locks and dowels	For connecting panels without visible screws	8 each
Instruction manual	Step-by-step assembly guide	1

Tools Required

Tools needed for assembly (not included in package).

Cross-head screwdriver (Phillips #2)
Hammer (for tapping dowels)
Measuring tape
Pencil (for marking if needed)

NOTE: Power drill can be used but set to low torque to avoid damaging wood.

Safety Instructions

Important safety information before beginning assembly.

Work on a clean, flat surface to prevent parts from rolling or falling.
Keep small parts away from children and pets to avoid choking hazards.
Wear safety glasses when hammering or drilling.
Lift with your legs, not your back – drawer components can be heavy.
Ensure all screws and connections are tight before use.

WARNING! Do not stand or sit on the drawer. It is designed for storage only.

Step-by-Step Assembly

Follow these steps in order to assemble the drawer unit.

Step 1: Attach side panels to front panel using dowels and cam locks. Insert dowels into front panel holes, align side panels, and tighten cam locks with screwdriver.
Step 2: Attach back panel to side panels using same method (dowels and cam locks).
Step 3: Slide bottom panel into grooves on side and front panels. Ensure it sits flush.
Step 4: Secure bottom panel with provided screws through pre-drilled holes in back panel.
Step 5: Attach metal drawer runners to both sides of drawer using screws provided. Ensure they are parallel and at same height.
Step 6: Check all connections are tight and drawer moves smoothly on runners.

TIP: Do not overtighten cam locks – turn until snug to avoid stripping.

Installation into Bed Frame

How to install assembled drawer into TARVA bed frame.

Slide bed frame aside to access under-bed space.
Align drawer runners with rails on bed frame (rails should be pre-installed).
Push drawer into frame until it clicks into place.
Test drawer operation – it should slide smoothly without catching.
Adjust runner position if drawer is uneven or sticks.

NOTE: TARVA bed frame must be assembled according to its own instructions before installing drawer.

Adjustments & Leveling

Fine-tuning for optimal performance.

Drawer alignment: Loosen runner screws slightly, adjust drawer position, retighten.
Smooth sliding: Apply furniture wax or paraffin to runners if drawer sticks.
Weight capacity: Do not exceed 55 lbs (25 kg) distributed evenly.
Stability check: Ensure bed frame is level on floor to prevent drawer misalignment.

Care & Maintenance

Keeping your drawer in good condition.

Clean with damp cloth and mild soap. Dry immediately.
Do not use abrasive cleaners or solvents on pine surface.
Periodically check and tighten screws and cam locks.
Apply wood conditioner annually if in dry climate to prevent cracking.

CAUTION! Avoid excessive moisture. Pine is untreated and can stain or warp if wet.

Specifications

Product name: TARVA Drawer
Article number: 803.607.05
Material: Solid pine, fiberboard bottom
Finish: Untreated pine (can be stained, painted, or oiled)
Dimensions (assembled): Width: 31.5" (80 cm), Depth: 17.75" (45 cm), Height: 7.875" (20 cm)
Weight capacity: 55 lbs (25 kg)
Weight (package): 15.4 lbs (7 kg)
Country of origin: Designed and quality tested by IKEA of Sweden

Warranty Information

IKEA limited warranty. This product is covered by IKEA's standard warranty terms. For details, visit www.ikea.com or contact your local IKEA store. Keep your receipt as proof of purchase.

NOTE: Warranty does not cover damage from improper assembly, modification, accidents, or normal wear and tear.

Troubleshooting

Problem	Possible Cause	Solution
Drawer won't slide smoothly	Runners misaligned or debris in tracks	Realign runners; clean tracks with dry cloth.
Drawer front not flush	Cam locks not fully tightened	Tighten cam locks; check dowel alignment.
Bottom panel bows	Excessive weight or not seated in grooves	Reduce weight; remove and reseat panel.
Screws won't tighten	Stripped holes or wrong screw used	Use wood filler to repair hole; use correct screw.
Drawer sticks out from bed frame	Runners installed backwards	Remove and reinstall runners with correct orientation.

Need help? Contact IKEA customer support at 1-888-888-4532 or visit www.ikea.com/us/en/customer-service.