IKEA TÄLLBYN 104.589.94 Table Lamp instructions manual

The IKEA TÄLLBYN 104.589.94 is a modern table lamp featuring a metal base, a fabric shade, and an integrated LED light source. It includes an in-line switch on the cord for easy operation. Designed for indoor use, it requires assembly and uses a standard E26/E27 bulb socket (LED bulb included). Below are key sections for safety, assembly, operation, care, and troubleshooting.

Features at a Glance

Key components: Metal base, Fabric shade, Integrated LED light source, Power cord with in-line switch.

Assembly Instructions

Unpack all parts and check contents against the parts list. Place on a clean, flat surface.

1. Attach the base: Screw the metal base onto the lamp stem by turning clockwise until firm.
2. Install the shade: Place the fabric shade over the bulb socket and secure it according to the provided locking mechanism (usually a twist or clip).
3. Route the cord: Ensure the power cord is untangled and exits from the designated opening in the base.
4. Insert the LED bulb (if replaceable model): Screw the provided LED bulb into the E26/E27 socket clockwise until snug. Do not overtighten.

WARNING! Ensure the lamp is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Setup

After assembly, plug the lamp into a standard electrical outlet.

1. Position the lamp: Place on a stable, level surface away from edges.
2. Power on: Use the in-line switch on the cord to turn the lamp ON/OFF.
3. Test operation: Switch on to verify the LED lights up properly.
4. Adjust placement: Ensure the lamp is not in contact with flammable materials or in a high-traffic area.

CAUTION! Do not use with dimmer switches unless specified. Ensure the outlet voltage matches the lamp rating.

Specifications

• Model: TÄLLBYN 104.589.94
• Type: Table Lamp
• Power Consumption: 7W (integrated LED)
• Light Output: Approximately 600 lumens
• Color Temperature: 2700K (Warm White)
• CRI (Color Rendering Index): >80
• Input Voltage: 120V AC, 60Hz (for North America)
• Lifetime: Up to 25,000 hours
• Materials: Metal base, Fabric shade, Plastic components
• Certifications: UL Listed (or equivalent regional safety standard)

Controls and Operation

The lamp is operated solely via the in-line switch on the power cord.

Switch Operation: Press the button on the switch to toggle between ON and OFF states. The lamp will remember the last state when plugged in.

Note: This model does not feature adjustable brightness or color settings. The integrated LED provides fixed warm white light.

Placement & Usage

Designed for indoor use on tables, desks, nightstands, or shelves.

1. Ensure the surface is stable, dry, and level.
2. Keep away from water, humidity, and heat sources (e.g., radiators, stoves).
3. Do not place where the cord can be tripped over or pinched.
4. Maintain at least 10 cm (4 inches) clearance around the lamp for ventilation.

Tip: Use as task lighting for reading or as ambient lighting in living spaces.

Replacing the Light Source

This model typically uses an integrated, non-replaceable LED. If the LED fails, the entire lamp may need replacement.

For models with a replaceable E26/E27 socket:

1. Unplug the lamp and allow to cool if it was recently on.
2. Remove the shade (if necessary) by twisting or unclipping.
3. Unscrew the old bulb counterclockwise and dispose of it properly.
4. Screw in a new LED bulb of equivalent specifications (max 7W, E26/E27 base).
5. Reattach the shade and plug in the lamp.

WARNING! Never use a bulb with higher wattage than recommended. Do not touch the LED with bare hands; use a cloth if necessary.

Safety Information

Read all instructions before use. Keep for future reference.

• For indoor use only. Not for outdoor or wet locations.
• Do not disassemble or modify the lamp. No user-serviceable parts inside.
• Unplug before cleaning or when not in use for extended periods.
• Keep out of reach of children and pets.
• Do not cover the lamp or place objects on it during operation.
• If the cord is damaged, discontinue use and contact IKEA support.

Care & Cleaning

Unplug the lamp and allow it to cool completely before cleaning.

1. Base & Shade: Wipe with a soft, dry cloth. For stubborn spots, use a slightly damp cloth. Do not immerse in water.
2. Fabric Shade: Use a vacuum with a soft brush attachment to remove dust. Do not use chemicals or detergents.
3. Cord & Switch: Wipe with a dry cloth. Ensure no moisture enters the switch housing.

CAUTION! Do not use abrasive cleaners, solvents, or spray liquids directly on the lamp.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included with the product or available at IKEA stores.

Support: For assembly help, spare parts, or product questions, contact IKEA customer service:

• Phone: 1-800-434-4532 (IKEA US)
• Website: www.ikea.com
• Visit your local IKEA store.

© Inter IKEA Systems B.V. The IKEA trademark and model name TÄLLBYN are owned by Inter IKEA Systems B.V.

Troubleshooting

Recycling: Dispose of the lamp and electronic components according to local regulations. Do not dispose of with household waste.

Service: For issues not resolved above, contact IKEA customer support.