IKEA STRÅLA 605.629.74 Pendant Lamp instructions manual
The IKEA STRÅLA 605.629.74 is a pendant lamp designed for ceiling mounting, featuring a metal shade and a textile-covered cord. It requires assembly and installation, which involves electrical wiring. Below are key sections for safety, parts included, assembly, installation, operation, care, and troubleshooting.
Parts Included
Before starting, check that all parts are present.
| Part Name | Quantity | Description |
|---|
| Lamp shade | 1 | Metal shade, white/black |
| Cord set | 1 | Textile-covered cord with plug and switch |
| Ceiling plate | 1 | Mounting plate with screw holes |
| Mounting screws | 2 | For securing ceiling plate |
| Cord grip | 1 | For securing cord to ceiling plate |
| Instruction manual | 1 | This document |
Safety Information
WARNING! Risk of electric shock and fire. Read all instructions before installation.
- Disconnect power at circuit breaker before installation.
- Installation must comply with local electrical codes.
- Use only with recommended light source (max wattage specified).
- Ensure ceiling can support lamp weight.
- Keep away from flammable materials.
- Do not use if cord or plug is damaged.
CAUTION! This luminaire is not suitable for mounting in locations where water jets are likely to occur.
Tools Required
- Phillips screwdriver
- Drill (if pre-drilling holes required)
- Wire strippers
- Voltage tester
- Ladder or step stool
Assembly Instructions
- Unpack all parts and lay them on a clean, flat surface.
- Attach the cord grip to the hole in the center of the ceiling plate.
- Thread the textile cord through the cord grip and the lamp shade's opening.
- Secure the cord inside the shade using the provided cord clamp (if applicable).
- Ensure all connections are tight and the shade hangs straight.
Tip: Do not fully tighten screws until final adjustment.
Installation & Mounting
- Turn off power at the circuit breaker.
- Determine mounting location on ceiling, ensuring it aligns with an electrical box.
- Hold ceiling plate against ceiling, mark screw holes.
- Drill pilot holes (if necessary) and secure ceiling plate with mounting screws.
- Ensure plate is firmly attached and level.
WARNING! Use appropriate anchors if not mounting into a wooden joist or electrical box.
Electrical Connection
WARNING! Electricity can kill. If unsure, hire a qualified electrician.
- From the ceiling electrical box, you will have live (black/brown), neutral (white/blue), and ground (green/yellow) wires.
- Connect the lamp cord wires: Live (brown) to ceiling live, Neutral (blue) to ceiling neutral, Ground (green/yellow) to ceiling ground.
- Use wire connectors (not included) to secure connections. Tuck wires neatly into box.
- Attach the assembled lamp's ceiling plate to the electrical box using the provided screws.
- Restore power and test the lamp using the cord switch.
Operation & Use
- Use the switch on the cord to turn the lamp ON/OFF.
- Adjust the hanging height by tying a knot in the cord above the cord grip (if desired).
- Use only LED or incandescent bulbs with an E27 base, max 13W LED or 60W incandescent.
- To change bulb: Ensure lamp is off and cool. Unscrew old bulb, screw in new bulb.
Note: The lamp is designed for indoor use only.
Care & Cleaning
- Turn off and unplug lamp before cleaning.
- Wipe metal shade with a soft, dry cloth.
- For textile cord, use a soft brush or vacuum with brush attachment.
- Do not use abrasive cleaners, solvents, or water.
CAUTION! Never immerse the lamp or cord in water.
Specifications
- Article Number: 605.629.74
- Type: Pendant lamp
- Material: Shade: Steel, epoxy/polyester powder coating. Cord: Textile.
- Color: White/Black
- Socket: 1 x E27
- Max Wattage: 13W LED or 60W incandescent
- Cord Length: 200 cm (approx.)
- Diameter: 30 cm
- Height: Adjustable
- Weight: 1.2 kg
Troubleshooting
| Symptom | Possible Cause | Corrective Action |
|---|
| Lamp does not light | Power off / Bulb faulty | Check circuit breaker; ensure cord switch is ON; try a new bulb. |
| Lamp flickers | Loose connection / Bulb type | Turn off power, check all wire connections; ensure bulb is properly screwed in and is compatible. |
| Lamp gets hot | Bulb wattage too high | Use a bulb with wattage at or below the maximum specified. |
| Shade wobbles | Loose assembly | Turn off power. Check and tighten all screws and the cord grip. |
| Switch on cord doesn't work | Faulty switch / wiring | Disconnect power. Check switch and cord for damage. May require replacement by electrician. |
For Support: Visit www.ikea.com or contact your local IKEA store.
WARNING! Any modification not specified by IKEA may void the warranty and create safety hazards.
IKEA STRÅLA 605.629.74 Pendant Lamp instructions manual © - All Rights Reserved 2025