IKEA SONGESAND 103.945.58 Wardrobe instructions manual

The IKEA SONGESAND 103.945.58 is a freestanding wardrobe featuring a classic design with hinged doors, adjustable shelves, and a clothes rail. Constructed from particleboard, fiberboard, and ABS plastic, it requires assembly. The package includes all necessary panels, hardware, fittings, and an Allen key. Below are key sections for safety, parts identification, step-by-step assembly, installation, care, and troubleshooting.

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Wardrobe panels (sides, top, bottom, back panels, shelves), doors, hinges, screws, dowels, cam locks, clothes rail, and Allen key.

Safety Instructions

Read all instructions before assembly. Ensure a safe working environment.

1. Work Area: Assemble on a clean, flat, protected surface to avoid scratches.
2. Lifting: The wardrobe is heavy; use two people for lifting and moving assembled unit.
3. Secure Assembly: Tighten all screws and fittings securely. An unsecured wardrobe can tip over.
4. Wall Anchoring: To prevent tipping, especially in households with children, the wardrobe MUST be securely anchored to the wall using the provided wall attachment device.
5. Tool Use: Use only the provided Allen key. Do not overtighten screws.

WARNING! Failure to anchor this furniture to the wall can result in serious or fatal tipping injury.

Step-by-Step Assembly

Follow the numbered steps in the included pictorial guide. This is a summary of the key stages.

1. Prepare Panels: Lay side panels flat. Insert dowels into pre-drilled holes as indicated.
2. Assemble Frame: Connect the bottom panel to the side panels using cam locks. Then attach the top panel.
3. Install Back Panels: Place the assembled frame upright. Slot the back panels into the grooves on the frame. Secure with provided screws.
4. Install Interior: Insert the clothes rail brackets into the side panels and secure. Place the adjustable shelves on the support pins.
5. Attach Doors: Mount hinges to the doors first. Then attach the doors to the side panels. Do not fully tighten hinge screws until alignment is complete.
6. Final Check: Ensure all cam locks are turned to the locked position. Tighten all screws securely.

Tip: Keep packaging away from children and pets during assembly.

Installation & Levelling

Once assembled, move the wardrobe to its final location.

1. Positioning: Place the wardrobe against the intended wall, ensuring there is space for doors to open fully.
2. Levelling: Use a spirit level on the top panel. Adjust the height of the adjustable feet (if present) at the bottom to achieve a level position.
3. Wall Anchoring: THIS STEP IS MANDATORY. Locate the solid wall stud. Use the provided wall attachment bracket and screws (not always included, may need to purchase separately for certain walls). Attach the bracket to the wardrobe's top rear section and securely screw it into the wall stud.

CAUTION! Do not place the wardrobe in damp areas like bathrooms, as moisture can damage the material.

Door Adjustment

If doors are uneven or not closing properly, adjust the hinges.

1. Height Adjustment: Loosen the screw on the hinge arm (usually the top one). Move the door up or down, then retighten.
2. Depth Adjustment: Turn the screw at the base of the hinge cup (inside the door hole) to move the door closer to or further from the frame.
3. Sideways Adjustment: Loosen the screws that attach the hinge plate to the side panel. Adjust the door left/right, then retighten.

Make small adjustments and check alignment after each turn.

Specifications

• Article Number: 103.945.58
• Dimensions (WxDxH): 120 cm x 60 cm x 201 cm (47 1/4" x 23 5/8" x 79 1/8")
• Max Load Shelf: 25 kg (55 lb) per shelf, evenly distributed.
• Max Load Clothes Rail: 30 kg (66 lb).
• Material: Particleboard, Fiberboard, Foil, ABS plastic, Steel.
• Finish: White, stained and lacquered.
• Door Type: Hinged.
• Weight: Approximately 65 kg (143 lb) when packaged.

Care & Maintenance

Proper care will extend the life of your wardrobe.

1. Cleaning: Wipe with a damp cloth wrung out in a mild soap solution. Dry immediately with a clean, soft cloth.
2. Avoid: Abrasive cleaners, scouring pads, or solvents (e.g., acetone).
3. Protection: Avoid prolonged direct sunlight and heat sources to prevent fading or warping.
4. Hardware Check: Periodically check and tighten hinge screws and cam locks.

CAUTION! Never use excessive water. Liquids can seep into seams and cause particleboard to swell.

Troubleshooting

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the packaging or available at IKEA stores.

For Assembly Support: Refer to the online assembly guide at IKEA.com using the article number.

For Missing Parts or Damage: Contact your local IKEA store or visit the IKEA website for spare parts service.

Customer Service: Visit www.IKEA.com or contact your local IKEA store.