IKEA SKATSJÖN 394.314.09 Sink instructions manual

The IKEA SKATSJÖN 394.314.09 is a stainless steel double bowl kitchen sink designed for durability and easy cleaning. It features two equal-sized bowls, a satin finish to minimize water spots and scratches, pre-drilled holes for faucet and accessories, and is compatible with most standard kitchen cabinets. Below are key sections for safety, features, installation, care, and troubleshooting.

Features at a Glance

Key components: Stainless steel double bowl, Mounting clips, Template, Drain assembly parts.

Safety Information

Read all instructions before installation.

1. Sharp Edges: Wear gloves when handling sink and cutout edges.
2. Heavy Object: Sink is heavy; use two people for lifting and positioning.
3. Secure Installation: Ensure sink is properly supported by cabinet frame to prevent collapse.
4. Tools: Use appropriate safety equipment (goggles, gloves) when cutting countertop.
5. Plumbing: Turn off water supply before connecting pipes. Check for leaks after installation.

WARNING! Improper installation can cause sink to detach, resulting in injury or property damage. Follow instructions carefully.

Package Contents

Unpack and verify all parts before starting installation.

• 1 x SKATSJÖN stainless steel sink
• 1 x Installation template
• 8 x Mounting clips
• 8 x Screws for mounting clips
• 2 x Drain assemblies (strainer, basket, tailpiece, locknut, washer)
• 1 x Instruction manual

Note: Faucet, supply lines, P-trap, and silicone sealant are NOT included.

Specifications

• Model: SKATSJÖN 394.314.09
• Color: Stainless steel (satin finish)
• Material Thickness: 0.8 mm (18 gauge)
• Bowl Depth: 20 cm (7.9") each
• Overall Depth (with rim): 22 cm (8.7")
• Weight: 8.5 kg (18.7 lbs)
• Drain Hole Diameter: 3.5" (89 mm) standard
• Recommended Countertop: Stone, quartz, solid surface, wood (minimum 3 cm/1.2" thickness)
• Certifications: Meets ANSI/NSF 51 for food equipment materials

Tools Required

Gather these tools before beginning installation.

1. Measuring tape
2. Pencil
3. Jigsaw or router with sink cutout bit
4. Drill with 1/4" drill bit
5. Screwdriver (Phillips)
6. Adjustable wrench
7. Plumber's putty or silicone sealant
8. Caulking gun
9. Safety goggles and gloves
10. Level

Installation Instructions

Follow these steps for undermount installation.

1. Prepare Cabinet: Ensure cabinet is level, sturdy, and has adequate front-to-back depth (min. 80 cm).
2. Template Placement: Position template on countertop where sink will be located. Center within cabinet. Trace outline with pencil.
3. Cut Countertop: Drill starter hole inside traced line. Use jigsaw to cut along line. Sand edges smooth.
4. Test Fit: Place sink into cutout from below. Ensure it sits flush with countertop underside. Adjust cutout if necessary.
5. Apply Sealant: Run bead of 100% silicone sealant along top edge of sink flange.
6. Mount Sink: Lift sink into position from below. Secure with mounting clips: attach clips to sink flange, then screw into countertop underside. Tighten evenly.
7. Check Level: Use level to ensure sink is even. Wipe excess sealant.
8. Cure Time: Allow sealant to cure 24 hours before using sink or connecting plumbing.

CAUTION! Do not overtighten mounting clips, as this can warp sink. Support sink during curing.

Connecting Plumbing

Connect drain and supply lines after sink is securely mounted.

1. Install Drains: Apply plumber's putty under drain flange. Insert into drain hole. Secure from below with washer and locknut. Tighten with wrench.
2. Connect Tailpieces: Attach tailpiece to drain assembly. Connect to P-trap. Ensure all connections are hand-tightened, then use wrench for final quarter-turn.
3. Install Faucet: Insert faucet through pre-drilled hole. Secure from below with mounting nut. Connect hot/cold supply lines.
4. Check for Leaks: Turn on water supply. Fill both bowls. Check connections for leaks. Tighten if necessary.

Tip: Use Teflon tape on threaded connections to prevent leaks.

Care & Cleaning

Proper care maintains appearance and longevity.

1. Daily Cleaning: Use mild dish soap, warm water, and soft cloth. Rinse and dry with clean cloth to prevent water spots.
2. Stain Removal: For mineral deposits, use vinegar solution. For grease, use baking soda paste. Always rinse thoroughly.
3. Do Not Use: Abrasive cleaners, steel wool, bleach, or ammonia-based products. They can damage finish.
4. Prevent Scratches: Use sink grid or mat. Avoid dropping heavy or sharp objects.
5. Odor Control: Pour baking soda and vinegar down drain monthly to keep pipes fresh.

CAUTION! Never use acidic cleaners (e.g., for toilets) on stainless steel.

Warranty Information

IKEA limited warranty: 25 years for stainless steel sink from original date of purchase. Warranty covers defects in material and workmanship under normal household use. Does not cover damage from improper installation, accidents, misuse, or lack of maintenance. Proof of purchase required. For warranty service, contact IKEA customer service or return to store.

Troubleshooting

For Support: Contact IKEA customer service at 1-888-888-4532 or visit www.ikea.com.