IKEA SINARP 094.052.23 Door instructions manual

The IKEA SINARP 094.052.23 is a door designed for compatibility with specific IKEA cabinet frames. It features a modern design, pre-drilled holes for hinges, and is ready for assembly. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Door panel, pre-installed hinge mounting plates, protective film.

Installation

Unpack and inspect contents. Ensure you have the correct tools (screwdriver, possibly a drill).

1. Identify hinge side: Determine left or right opening based on cabinet design.
2. Attach hinges: Align hinges with pre-drilled holes on door interior; secure with provided screws.
3. Mount door to cabinet: With help if needed, align hinges to cabinet frame; secure hinges to frame.
4. Remove protective film: Peel off film carefully after installation to avoid adhesive residue.

WARNING! Door can be heavy; use caution when lifting. Ensure cabinet is stable and level before mounting.

First-Time Setup

After mounting, perform initial adjustments.

1. Check alignment: Open and close door; ensure it sits flush with cabinet frame and adjacent doors.
2. Adjust hinges: Use screwdriver to adjust hinge screws for height, depth, and side-to-side alignment.
3. Test operation: Door should open smoothly and stay closed without sagging.
4. Install handle/pull: If not pre-installed, attach handle according to separate instructions.

CAUTION! Do not over-tighten screws; this may strip the particleboard.

Specifications

• Product Name: SINARP door.
• Article Number: 094.052.23.
• Material: Particleboard, foil.
• Finish: White, matte.
• Edge Banding: ABS plastic (white).
• Hinge Compatibility: IKEA UTDRAG or similar concealed hinges.
• Weight: Varies by size; refer to packaging.
• Environmental Info: Meets IKEA standards for low formaldehyde emissions.

Controls and Settings

Adjustment is via hinge screws. No electronic controls.

Hinge Adjustment: Three screws typically: one for height (up/down), one for depth (in/out), one for side-to-side (left/right).

Alignment Goals: Door even with frame; consistent gap between doors; smooth closing without force.

Connecting to Cabinet

Requires compatible IKEA cabinet frame and hinges.

1. Verify compatibility: Check IKEA product listing or manual for frame/door compatibility.
2. Prepare cabinet: Ensure frame is assembled, level, and securely mounted to wall if applicable.
3. Mount hinges to door: As per Installation steps.
4. Attach door to cabinet: Align hinge plates to mounting plates on cabinet interior; click or screw into place.

Tip: Have a second person hold door during mounting for easier alignment.

Adjustment & Alignment

Fine-tune after initial installation.

1. Height adjustment: Turn hinge screw to raise or lower door relative to cabinet.
2. Depth adjustment: Adjust screw to move door closer to or farther from cabinet frame.
3. Side adjustment: Adjust screw to shift door left or right for even gaps.
4. Check gaps: Aim for consistent 2-3mm gap between doors and frame.
5. Test close: Ensure door closes fully and latch engages if present.

WARNING! Make small adjustments (quarter turns) and test frequently.

Care & Cleaning

Use mild cleaning agents only.

Clean with damp cloth and mild detergent; dry immediately. Avoid abrasive cleaners, scouring pads, or solvents that may damage foil finish.

CAUTION! Do not soak; moisture can cause particleboard to swell.

Regulatory Information

IKEA of Sweden AB. Complies with applicable furniture safety standards. Trademarks owned by Inter IKEA Systems B.V. For support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

Replacement: If damaged, contact IKEA for spare parts (provide article number 094.052.23).

Service: www.ikea.com; local IKEA customer service.