IKEA SEKTION 094.022.91 Cabinet Frame instructions manual

The IKEA SEKTION 094.022.91 is a cabinet frame designed for the SEKTION kitchen system. It is a modular component requiring assembly, featuring adjustable legs, a rigid frame structure, and compatibility with various SEKTION doors, drawers, and interior fittings. Below are key sections for safety, parts list, assembly, installation, adjustment, and care.

Parts and Hardware Included

Key components: Cabinet frame panels, adjustable legs, cam locks, dowels, screws, wall mounting brackets, and assembly instructions.

Tools Required

Gather these tools before starting assembly.

1. Phillips screwdriver (or cordless drill with Phillips bit).
2. Hammer (for gently tapping dowels).
3. Level (at least 24 inches).
4. Tape measure.
5. Pencil.
6. Stud finder (recommended for wall mounting).

NOTE: Using the correct tools ensures proper assembly and prevents damage to parts.

Safety Instructions

Read all instructions before assembly. Ensure a safe working environment.

1. Assembly requires two people due to size and weight of panels.
2. Keep small hardware away from children to prevent choking.
3. Assemble on a soft, clean surface to avoid scratching panels.
4. When mounting to wall, always secure into wall studs for stability.
5. Do not stand on or place excessive weight on the cabinet before it is fully secured to the wall.

WARNING! Failure to secure cabinet to wall can result in tipping, causing serious injury or death. Always use provided wall mounting brackets and attach to structural wall studs.

Assembly Steps

Follow steps in order. Do not fully tighten all screws until frame is squared.

1. Attach Legs: Screw the four adjustable legs into the pre-drilled holes on the bottom panel.
2. Connect Side Panels: Insert dowels into side panels as shown in diagram. Align side panels with top and bottom panels.
3. Lock Cam Fittings: Insert cam locks into corresponding holes and turn 90° clockwise to lock panels together. Ensure all locks are fully engaged.
4. Install Back Panel: Place the back panel into the groove on the rear of the frame. Secure with provided screws along the edges.
5. Square the Frame: Check that the cabinet is square by measuring diagonally from corner to corner. Measurements should be equal. Adjust if necessary before final tightening.

Tip: Lay the cabinet on its back during assembly for easier access to cam locks and screws.

Installation and Mounting

Proper wall mounting is critical for safety.

1. Position Cabinet: Move assembled frame to desired location. Adjust legs so cabinet is roughly level and at correct height.
2. Locate Wall Studs: Use a stud finder to locate at least two wall studs where the cabinet will hang. Mark their centers with a pencil.
3. Attach Mounting Brackets: Secure the metal wall mounting brackets to the inside top rear of the cabinet frame using provided screws.
4. Secure to Wall: With a helper holding the cabinet firmly against the wall, align the brackets with the stud marks. Drive long mounting screws through the bracket holes and into the center of the wall studs. Tighten securely.
5. Final Check: Gently try to pull the cabinet away from the wall. It should not move. Re-tighten all connections if needed.

CAUTION! Do not rely on drywall anchors alone. Cabinets must be anchored into wooden or metal studs.

Adjusting Cabinet Leveling

Use the adjustable legs to achieve a perfectly level and stable installation.

1. Place a level on top of the cabinet frame.
2. Turn the legs clockwise to raise that corner, or counter-clockwise to lower it.
3. Check for level both front-to-back and side-to-side.
4. Ensure all four legs are firmly in contact with the floor to prevent rocking.

Note: On uneven floors, you may need to adjust legs significantly. The cabinet top must be level for proper door and drawer operation.

Installing Doors and Drawers

The SEKTION frame is designed for use with IKEA's hinge and runner systems.

1. Door Hinges: Attach hinges to the door according to the door's specific instructions. Then clip the hinges onto the mounting plates installed inside the cabinet frame.
2. Drawer Runners: Attach the runner halves to the cabinet side panels at the desired height, using the measurement grid printed on the panel. Attach the other halves to the drawer box.
3. Alignment: After attaching, open and close doors/drawers. Use the adjustment screws on the hinges and runners to align doors evenly and ensure smooth operation.

Tip: Install doors and drawers after the cabinet is securely mounted and leveled.

Specifications and Dimensions

• Frame Model: SEKTION 094.022.91
• Overall Dimensions (HxWxD): Refer to IKEA product page for exact size (e.g., 30" H x 15" W x 15" D is common).
• Material: Particleboard, foil, ABS plastic, steel.
• Finish: White (as per model number).
• Max Load Weight: Distributed weight as specified for shelf type. Do not exceed recommended load.
• Compatibility: Designed for use with SEKTION doors, drawers, shelves, and interior organizers.

Care and Maintenance

Clean with a damp cloth and mild detergent. Wipe dry immediately.

DO NOT: Use abrasive cleaners, scouring pads, or harsh chemicals. Avoid excessive moisture. Do not place hot items directly on surfaces without protection.

Periodically Check: Tighten any loose screws or cam locks. Verify that wall mounting remains secure.

Warranty and Support

This IKEA product is covered by a limited warranty. For details, see the IKEA warranty brochure included with your purchase or visit www.IKEA.com.

Customer Support: Visit your local IKEA store or contact IKEA customer service via their website for spare parts, assembly advice, or warranty claims.

Spare Parts: Most small hardware (dowels, cam locks, screws) can be obtained free of charge from IKEA returns & exchanges desk.

Troubleshooting

For persistent issues: Consult online assembly videos at IKEA.com or contact customer support.