IKEA SEKTION 093.889.35 Base Cabinet instructions manual

The IKEA SEKTION 093.889.35 is a base cabinet designed for kitchen storage, featuring a durable construction, adjustable shelves, soft-closing doors/drawers, and compatibility with SEKTION system fronts and interior organizers. Below are key sections for safety, parts list, assembly, installation, adjustment, care, and troubleshooting.

Parts & Hardware Included

Key components: Cabinet frame, back panel, adjustable shelves, door/drawer fronts (if included), hinges, runners, screws, dowels, cam locks, wall mounting brackets.

Tools Required

Gather tools before starting assembly.

1. Phillips screwdriver (size #2) or cordless drill with screwdriver bit.
2. Hammer (for tapping dowels).
3. Level (for installation alignment).
4. Tape measure.
5. Pencil (for marking).
6. Stud finder (for wall mounting).

WARNING! Use correct tools to avoid damaging parts or injury.

Safety Instructions

Read all instructions before assembly.

1. Work on clean, flat surface to prevent tipping.
2. Use two people for lifting and positioning cabinet.
3. Secure cabinet to wall studs using provided brackets to prevent tipping.
4. Keep small hardware away from children to avoid choking hazard.
5. Do not exceed maximum load: 55 lbs per shelf, 100 lbs total for base cabinet.

CAUTION! Cabinet is heavy; lift with legs, not back. Ensure wall mounting is secure.

Assembly Steps

Follow numerical order on pre-drilled holes.

1. Frame assembly: Connect side panels to top/bottom panels using dowels and cam locks. Tighten cam locks clockwise with screwdriver.
2. Back panel: Insert back panel into grooves on rear of frame. Secure with provided screws along edges.
3. Shelves: Insert shelf support pins into desired holes. Place adjustable shelves on pins.
4. Hinge plates: Attach hinge plates to inside of side panels at marked locations using screws.
5. Drawer runners (if applicable): Attach runner halves to cabinet sides and drawer boxes per diagram.
6. Leveling legs: Screw adjustable legs into bottom panel corners; adjust later during installation.

Tip: Do not fully tighten cam locks until all frame joints are aligned.

Installation to Wall & Adjacent Cabinets

For secure and level installation.

1. Position cabinet in desired location, leaving access for plumbing/electrical if needed.
2. Use level to ensure cabinet is plumb; adjust leveling legs as needed.
3. Locate wall studs with stud finder; mark positions.
4. Attach wall mounting brackets to upper rear of cabinet frame.
5. Lift cabinet against wall; secure brackets to wall studs with long screws provided.
6. For multiple cabinets: Clamp cabinets together, align faces, then secure with connecting screws through side panels.
7. Check doors/drawers for smooth operation; adjust as needed.

WARNING! Cabinets must be anchored to wall studs. Drywall anchors are not sufficient for safety.

Door & Drawer Adjustment

Fine-tune for alignment and smooth close.

Doors:

1. Height adjustment: Turn hinge screw at door top/bottom to raise/lower door.
2. Side-to-side: Loosen hinge plate screws, shift door left/right, retighten.
3. Depth: Adjust screw on hinge to move door closer/further from frame.

Drawers:

1. Height: Adjust screws on rear of runner to raise/lower drawer front.
2. Side alignment: Loosen runner mounting screws, adjust drawer left/right.
3. Soft-close: If not closing smoothly, check runner mechanism for debris.

Note: Make small adjustments; test operation after each turn.

Interior Organization

Maximize storage with SEKTION accessories.

• Pull-out trays: Install on shelf runners for easy access.
• Dividers: Add to shelves for organizing plates/cutlery.
• Drawer organizers: Insert into drawers for utensils.
• Waste sorting bin: Compatible with base cabinet for recycling.

Tip: Measure interior before purchasing accessories.

Care & Maintenance

Clean with damp cloth; avoid abrasive cleaners.

1. Wipe surfaces with mild soap and water; dry immediately.
2. For stubborn stains, use non-abrasive cleaner; test on hidden area first.
3. Do not use solvents, ammonia, or abrasive pads.
4. Tighten hinges/screws annually to maintain stability.
5. Check leveling legs periodically; readjust if floor settles.

CAUTION! Avoid excess moisture; do not soak panels.

Specifications

• Model: SEKTION 093.889.35 Base Cabinet.
• Dimensions: Height 30", Width 36", Depth 24" (adjustable with legs).
• Material: Particleboard with melamine foil, ABS edging.
• Finish: White, Ash, or other SEKTION finishes.
• Weight capacity: 55 lbs per shelf, 100 lbs total distributed load.
• Hinge type: Soft-closing, adjustable (110° opening).
• Runner type: Full-extension soft-close (for drawers).
• Compatibility: SEKTION fronts, interior organizers.

Warranty & Support

IKEA limited warranty: 10 years for SEKTION cabinets. Proof of purchase required.

For missing parts or assembly help:

1. Visit IKEA store with product number (093.889.35).
2. Contact IKEA customer support: 1-888-888-4532.
3. Online: www.IKEA-usa.com > Support > Assembly Instructions.

Note: Warranty does not cover improper installation or misuse.

Troubleshooting

Replacement parts: Hinges, runners, shelves available at IKEA or via customer service.

Service: 1-888-888-4532; www.IKEA-usa.com