IKEA SEGERÖN 605.108.00 Bar Table instructions manual

The IKEA SEGERÖN 605.108.00 is a stylish and functional bar table designed for indoor use. It features a sturdy particleboard and fiberboard construction with a white stained oak veneer finish, metal legs for stability, and a height suitable for bar stools. This manual provides essential information for safe assembly, use, care, and troubleshooting of your new bar table.

1. Parts & Tools Included 2. Safety Instructions 3. Assembly Instructions 4. Product Specifications 5. Care & Maintenance 6. Weight & Load Capacity 7. Warranty Information 8. Troubleshooting

Parts & Tools Included

Before assembly, verify all parts are present. Check the packaging for small items.

Part NumberDescriptionQuantity
ATable top1
BMetal leg4
CLeg connector plate4
DScrew (for leg to plate)16
EAllen key (tool)1
FPlastic foot cap4
-Instruction manual1

NOTE: Some screws may be pre-attached to parts. Do not discard packaging until assembly is complete.

Safety Instructions

For your safety and to ensure proper assembly, please read all instructions before beginning.

  1. Assembly Surface: Assemble on a soft, clean surface (e.g., carpet, blanket) to prevent scratching the table top.
  2. Adult Assembly: This product requires assembly by an adult. Keep children and pets away from small parts during assembly.
  3. Tool Use: Use only the provided Allen key. Do not overtighten screws.
  4. Stability: Ensure all legs are firmly attached and the table is level before use.
  5. Weight Limit: Do not exceed the maximum load capacity (see Section 6).

WARNING! To prevent tipping, do not climb, stand, or sit on the table. Do not place excessively heavy items on one side.

Assembly Instructions

Follow these steps in order. Estimated assembly time: 15-25 minutes.

  1. Attach Connector Plates: Turn the table top (A) upside down on a protected surface. Position a leg connector plate (C) into each of the four pre-marked corner slots on the underside of the table top.
  2. Secure Plates: Using the provided screws (D) and Allen key (E), screw each plate firmly to the table top. Ensure the plate is flush and secure.
  3. Attach Legs: Take one metal leg (B). Align the holes at the top of the leg with the holes on the connector plate (C). Insert and tighten the four screws (D) using the Allen key. Repeat for all four legs.
  4. Attach Foot Caps: Press a plastic foot cap (F) onto the bottom of each metal leg to protect your floor.
  5. Final Check: Carefully turn the table right-side up. Check that all legs are firmly attached and the table is stable and does not wobble. Tighten any loose screws if necessary.

Tip: Assemble the table in the room where it will be used to avoid moving the heavy assembled product.

Product Specifications

Care & Maintenance

Proper care will extend the life and appearance of your table.

  1. Cleaning: Wipe the table top with a damp cloth wrung out in a mild soap solution. Wipe dry immediately with a clean, soft cloth.
  2. Stain Removal: For stubborn stains, use a furniture polish recommended for veneer surfaces. Always test in an inconspicuous area first.
  3. Protection: Use coasters under glasses and placemats under hot dishes to prevent heat marks, water rings, and scratches.
  4. Avoid: Do not use abrasive cleaners, scouring pads, or harsh chemicals. Avoid prolonged exposure to direct sunlight and high humidity.
  5. Legs & Feet: Clean metal legs with a dry or slightly damp cloth. Check plastic feet periodically for wear.

CAUTION! Never soak the table or allow liquids to pool on the surface, as this can damage the veneer and cause swelling.

Weight & Load Capacity

This table is designed for typical household use.

IMPORTANT: Exceeding the load capacity can cause permanent damage to the structure, leading to instability or breakage. The load capacity refers to static weight, not dynamic force (e.g., leaning, pushing).

Warranty Information

This IKEA product is covered by the IKEA commercial warranty. Refer to the IKEA warranty terms provided in the IKEA store or on www.ikea.com for your country.

General Coverage: The warranty covers material and manufacturing defects for a specified period from the date of purchase under normal household use and following the assembly and care instructions.

Not Covered: Damage resulting from improper assembly, accident, modification, commercial use, neglect, or failure to follow care instructions is not covered.

Support: For warranty claims or missing parts, please contact your local IKEA store with your receipt and article number (605.108.00).

Troubleshooting

IssuePossible CauseCorrective Action
Table wobblesUneven floor; loose legsCheck floor level. Turn table upside down and tighten all screws connecting legs to the table top. Adjust plastic foot caps if necessary.
Legs difficult to attachMisaligned holesEnsure the connector plate (C) is correctly seated in the slot on the table top before attempting to attach the leg.
Scratches on surface during assemblyAssembly on hard surfaceAlways assemble on a soft, protective surface like a blanket or carpet.
White veneer looks discoloredSun exposure or chemical spillPrevent further direct sunlight. For stains, clean gently as per Care instructions. Some fading may be irreversible.
Missing part(s)Packaging errorContact your nearest IKEA store customer service with your receipt and article number to order missing parts.

Re-tightening: It is recommended to check and tighten the leg screws a few weeks after initial assembly, as materials may settle.

IKEA Customer Support: Visit www.ikea.com for your local store contact information.

IKEA SEGERÖN 605.108.00 Bar Table instructions manual © - All Rights Reserved 2025