IKEA SEGERÖN 105.108.12 Table instructions manual

The IKEA SEGERÖN 105.108.12 is a versatile and sturdy table designed for various indoor uses. This manual provides essential information for safe assembly, proper use, care, and troubleshooting. Please read all instructions carefully before beginning assembly to ensure correct setup and optimal performance.

1. Parts & Tools Included 2. Safety Information 3. Assembly Instructions 4. Specifications 5. Care & Maintenance 6. Proper Use 7. Troubleshooting 8. Warranty & Support

Parts & Tools Included

Before assembly, verify all parts are present. Key components: Tabletop, Legs, Mounting hardware, Allen key.

Part Name	Description	Quantity
Tabletop	Main surface panel	1
Leg	Support leg with pre-attached fittings	4
Mounting screw	For attaching legs to tabletop	8
Allen key	Tool for tightening screws	1
Instruction manual	This document	1

Note: Check packaging for all items. Contact IKEA if any part is missing.

Safety Information

Important safety guidelines to prevent injury and damage.

Assembly Surface: Assemble on a soft, clean surface to avoid scratching the tabletop.
Lifting: The tabletop is heavy; use two people for lifting and positioning.
Tool Use: Use only the provided Allen key. Do not overtighten screws.
Stability: Ensure all legs are firmly attached before using the table.
Children: Keep children away from assembly area to avoid ingestion of small parts.

WARNING! Failure to follow safety instructions may result in injury or product damage.

Assembly Instructions

Follow these steps in order for correct assembly.

Prepare: Unpack all parts and lay them on a protected surface.
Position Tabletop: Place the tabletop upside down on a soft cloth or cardboard.
Attach Legs: Align one leg with the pre-drilled holes on the underside of the tabletop. Insert two mounting screws and tighten partially with the Allen key. Repeat for all four legs.
Final Tightening: Once all legs are attached, go back and fully tighten all screws securely.
Upright Position: Carefully turn the table right-side up with assistance.
Check Stability: Gently rock the table to ensure it is stable and does not wobble.

Tip: Do not fully tighten the first screw on each leg until all screws are started; this allows for minor adjustments.

Specifications

Product Name: SEGERÖN
Article Number: 105.108.12
Dimensions (L x W x H): Approximately 120cm x 60cm x 74cm.
Tabletop Material: Particleboard, Ash veneer, Clear acrylic lacquer.
Leg Material: Steel, Epoxy/polyester powder coating.
Max Load: 50 kg evenly distributed.
Weight: Approximately 15 kg.
Design: IKEA of Sweden

Care & Maintenance

Proper care will extend the life and appearance of your table.

Cleaning: Wipe the surface with a soft, damp cloth. Dry immediately with a clean, dry cloth.
Stains: For stubborn stains, use a mild soap solution. Never use abrasive cleaners, scouring pads, or solvents.
Protection: Use coasters under glasses and placemats under hot dishes to prevent marks and heat damage.
Environment: Avoid placing in direct sunlight or near heat sources to prevent fading or warping.
Inspection: Periodically check and tighten leg screws if necessary.

CAUTION! Never soak the table or allow liquids to pool on the surface or run down the legs.

Proper Use

To ensure safety and durability, use the table as intended.

Designed for indoor residential use (dining, working, etc.).
Do not stand, sit, or climb on the table.
Do not exceed the maximum load capacity.
Ensure the table is on a level floor to prevent wobbling.
For adjustable leg models, adjust all legs to the same height.

Note: Misuse, such as using the table as a workbench or step ladder, voids the warranty and is unsafe.

Troubleshooting

Issue	Possible Cause	Solution
Table wobbles	Uneven floor; loose legs	Check floor level; tighten all leg mounting screws securely. Use felt pads under legs if floor is uneven.
Scratches on surface	Abrasive cleaning or objects	Use recommended cleaning methods. Minor scratches can sometimes be lessened with a furniture polish recommended for lacquered surfaces.
Leg will not attach	Misaligned holes	Ensure the leg is oriented correctly. Do not force; gently align the fittings with the holes.
Stain on tabletop	Liquid spill	Clean immediately with a damp cloth. For set-in stains, use a mild soap solution.
Screw won't tighten	Stripped thread	Do not overtighten. If thread is damaged, contact IKEA for a replacement part.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms for details.

For Assembly Help or Missing Parts: Visit the IKEA website or contact your local IKEA store.

IKEA Customer Support: Visit www.ikea.com for your country or call the customer service number listed on your receipt.

Recycling: At the end of its life, disassemble the table and dispose of materials according to local recycling regulations.