IKEA SANDSHULT 504.564.03 Bracket instructions manual

The IKEA SANDSHULT 504.564.03 is a wall bracket designed for mounting flat-screen TVs and monitors. It features a slim profile, adjustable tilt, and secure VESA mounting compatibility. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Tools Required 4. Specifications 5. Installation Steps 6. Mounting Your TV 7. Adjusting the Tilt 8. Safety Information 9. Care & Maintenance 10. Warranty Information 11. Troubleshooting

Features at a Glance

Key components: Wall plate, mounting arms, TV mounting plate, hardware kit, cable management clips.

FeatureDescription
VESA CompatibilitySupports VESA patterns up to 400x400mm
Tilt AdjustmentAdjustable tilt for optimal viewing angle
Wall PlateSecure mounting to wall studs
Cable ManagementIntegrated clips for organizing cables
Hardware KitIncludes screws, wall anchors, and spacers
TV Mounting PlateAttaches directly to your TV
Level IndicatorBuilt-in bubble level for easy installation
MaterialDurable steel construction
FinishBlack powder-coated finish
Weight CapacitySupports TVs up to 50 lbs (22.7 kg)

Package Contents

Unpack and verify all components before installation.

  1. Wall plate (1 piece)
  2. TV mounting plate (1 piece)
  3. Mounting arms (2 pieces)
  4. Hardware kit (screws, wall anchors, spacers)
  5. Cable management clips (2 pieces)
  6. Instruction manual (this document)

WARNING! Do not proceed if any parts are missing or damaged. Contact IKEA customer service for replacement parts.

Tools Required

Gather these tools before beginning installation.

  1. Stud finder
  2. Power drill
  3. Phillips screwdriver
  4. Level
  5. Pencil
  6. Tape measure
  7. Socket wrench (optional)

CAUTION! Use appropriate safety equipment when drilling and mounting.

Specifications

Installation Steps

Follow these steps carefully for secure installation.

  1. Locate Studs: Use stud finder to locate wall studs. Mark center of studs with pencil.
  2. Position Wall Plate: Hold wall plate against wall at desired height. Use level to ensure it's straight.
  3. Mark Drill Holes: Mark drilling points through wall plate holes.
  4. Drill Pilot Holes: Drill pilot holes at marked points using appropriate drill bit for your wall type.
  5. Secure Wall Plate: Align wall plate with pilot holes and secure using provided screws. Ensure all screws are tight.
  6. Attach Mounting Arms: Connect mounting arms to wall plate using provided hardware.
  7. Install TV Plate: Attach TV mounting plate to your TV using VESA pattern screws.
  8. Mount TV: With assistance, lift TV and hook TV plate onto mounting arms.
  9. Secure TV: Use safety screws to secure TV plate to mounting arms.
  10. Cable Management: Route cables through cable management clips for neat appearance.

Mounting Your TV

Proper TV attachment is crucial for safety.

  1. Check TV VESA pattern in your TV manual.
  2. Select appropriate screws from hardware kit.
  3. Attach TV mounting plate to TV using four screws minimum.
  4. Ensure all screws are tightened securely but do not overtighten.
  5. Verify TV is securely attached before lifting.

Tip: Always have a second person assist when mounting the TV.

Adjusting the Tilt

The bracket allows tilt adjustment for optimal viewing.

  1. Loosen tilt adjustment screws on both sides of mounting arms.
  2. Gently tilt TV to desired angle.
  3. Tighten adjustment screws securely.
  4. Test stability by gently pushing on top and bottom of TV.

WARNING! Do not exceed tilt range limits. Ensure screws are tight after adjustment.

Safety Information

Closed Captions: Enable in DVD setup (On/Off). Parental Controls: Block by movie/TV ratings in FEATURES menu (password 9999).

Care & Maintenance

Periodic maintenance ensures long-term safety and performance.

  1. Check all screws and connections every 6 months.
  2. Tighten any loose hardware immediately.
  3. Clean with dry cloth only; no liquids or chemicals.
  4. Inspect wall mounting points for signs of stress.
  5. Ensure cables are not pulling on connections.

CAUTION! Do not use bracket if any damage is detected. Contact IKEA for replacement.

Warranty Information

IKEA SANDSHULT 504.564.03 comes with a 10-year limited warranty. This warranty covers defects in materials and workmanship. Warranty does not cover improper installation, misuse, or damage from accidents. For warranty claims, contact IKEA customer service with proof of purchase. For support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

SymptomPossible CauseCorrective Action
Bracket feels looseLoose screwsTighten all screws on wall plate and TV plate.
TV not levelUneven installationLoosen wall plate screws, adjust with level, retighten.
Cannot tilt TVTilt screws too tightLoosen tilt adjustment screws, adjust angle, retighten.
TV too close to wallIncorrect spacer useAdd spacers between TV and mounting plate.
Cables visiblePoor cable managementUse cable clips to route cables behind TV.
Mounting holes don't alignWrong VESA patternVerify TV VESA pattern and use correct holes.
Wall anchors not holdingWrong wall typeUse appropriate anchors for your wall material.

Professional Installation: If unsure, hire a professional installer.

Customer Service: 1-888-888-4532; www.ikea.com

IKEA SANDSHULT 504.564.03 Bracket instructions manual © - All Rights Reserved 2025