IKEA RÄNNILEN 094.158.73 Water Trap instructions manual

The IKEA RÄNNILEN 094.158.73 is a water trap designed to prevent unpleasant odors from the drain system from entering your living space. It is typically installed under sinks, showers, or other plumbing fixtures. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Installation 4. Specifications 5. Operation & Maintenance 6. Cleaning 7. Regulatory Information 8. Troubleshooting

Features at a Glance

Key components: Water trap body, Sealing gaskets, Connection nuts, Outlet pipe, Inspection opening.

Feature	Description
Material	Durable plastic construction
Sealing System	Integrated gaskets for leak-proof connection
Inspection Opening	Allows for easy cleaning and blockage removal
Universal Connection	Fits standard 40mm (1½") waste pipes
Water Seal	Maintains a water barrier to prevent sewer gases
Compact Design	Suitable for tight spaces under sinks and basins

Safety Information

Read all instructions before installation and use.

Ensure the water trap is compatible with your plumbing system.
Wear protective gloves during installation to prevent injury.
Do not use chemical drain cleaners that may damage the plastic.
Keep away from open flames or high heat sources.

WARNING! Incorrect installation may lead to leaks and water damage. Ensure all connections are tight and sealed.

Installation

Unpack and inspect all parts. Ensure you have the necessary tools: adjustable wrench, pipe cutter (if needed), sealant tape.

Turn off the water supply and disconnect the existing trap if present.
Clean the pipe ends and apply sealant tape to threaded connections.
Assemble the water trap by connecting the body to the sink outlet and the waste pipe.
Hand-tighten all nuts, then use an adjustable wrench for a final quarter turn. Do not overtighten.
Run water to check for leaks. Tighten further if necessary.

CAUTION! Ensure the trap is installed with a slight downward slope towards the drain to ensure proper drainage.

Specifications

Product Code: 094.158.73
Material: Polypropylene (PP) plastic
Inlet/Outlet Size: 40mm (1½ inches)
Water Seal Depth: Approximately 50mm
Color: White
Operating Temperature: 0°C to 80°C (32°F to 176°F)
Compatibility: Designed for IKEA RÄNNILEN series sinks and standard plumbing

Operation & Maintenance

The water trap operates automatically by maintaining a water seal. Regular maintenance prevents blockages and odors.

Run water through the trap weekly if the fixture is not used regularly to prevent the seal from drying out.
Check periodically for slow drainage, which may indicate a partial blockage.
Use the inspection opening to clear minor blockages without disassembling the entire trap.

Tip: Pouring a mixture of baking soda and vinegar followed by hot water can help maintain clean pipes.

Cleaning

Unclog and clean the trap regularly to ensure optimal performance.

Place a bucket under the trap to catch residual water.
Unscrew the inspection opening or the bottom clean-out plug.
Remove any debris or buildup.
Rinse the parts with warm water and reassemble.
Run water to re-establish the seal and check for leaks.

CAUTION! Do not use abrasive cleaners or tools that may scratch the plastic and cause leaks.

Regulatory Information

This product complies with relevant EU plumbing standards and directives. It is designed for use in residential drainage systems. Copyright © IKEA. RÄNNILEN is a trademark of Inter IKEA Systems B.V. For support, visit www.ikea.com or contact your local IKEA customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Foul odor from drain	Water seal evaporated or trap dry	Run water to refill the trap. Check for proper installation.
Water leaking from connections	Loose nuts or damaged gasket	Tighten connections. Replace gasket if torn or worn.
Slow drainage	Blockage in the trap or pipe	Clean the trap via the inspection opening. Use a plumber's snake for deeper blockages.
Gurgling sounds	Ventilation issue or partial blockage	Ensure the main vent stack is clear. Clean the trap.
Trap is loose	Nuts not tightened properly or missing washer	Disassemble, check all parts are present, and reassemble tightly.

Replacement: If the trap is cracked or damaged, replace it entirely. Do not attempt to repair with sealants.

Service: For installation issues or product defects, contact IKEA customer service or visit www.ikea.com.