IKEA RUNMARÖ 205.513.12 Cabinet instructions manual

The IKEA RUNMARÖ 205.513.12 is a wall-mounted cabinet designed for bathroom or hallway storage, featuring a white finish, tempered glass door, and adjustable shelves. Constructed from particleboard with foil and ABS plastic edging, it requires assembly and proper wall mounting. Below are key sections for safety, parts list, assembly steps, installation, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Wall Mounting Installation 6. Adjusting Shelves 7. Care & Maintenance 8. Specifications 9. Troubleshooting 10. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Cabinet frame, tempered glass door, adjustable shelves, mounting brackets, screws, wall anchors, cam locks, dowels.

Part Name	Quantity	Description
Cabinet back panel	1	Main rear panel with pre-drilled holes
Side panels	2	Left and right cabinet sides
Top/Bottom panels	2	Upper and lower frame pieces
Tempered glass door	1	Hinged door with handle
Adjustable shelves	2	Removable interior shelves
Mounting brackets	2	Metal brackets for wall attachment
Cam locks & dowels	Set	For connecting panels
Screws & wall anchors	Set	For securing to wall studs
Door hinge screws	4	For attaching door to frame
Instruction manual	1	This document

Tools Required

Tools not included; gather before starting.

Phillips screwdriver (size #2).
Hammer (for wall anchors if needed).
Drill with appropriate bits (for wall mounting).
Level (to ensure cabinet is straight).
Pencil (for marking wall).
Tape measure.

NOTE: Using correct tools ensures proper assembly and safety.

Safety Instructions

Read all instructions before assembly. Ensure safe handling and installation.

Assembly requires two people to avoid injury or damage.
Place cabinet on soft surface during assembly to prevent scratches.
Wall mounting must be into solid wall studs or using provided anchors for drywall.
Do not exceed maximum load capacity: 22 lbs (10 kg) per shelf.
Keep away from excessive moisture unless installed in bathroom with proper ventilation.

WARNING! Cabinet is heavy; lift with care. Ensure secure wall mounting to prevent tipping.

Assembly Steps

Follow numerical order for correct assembly.

Lay back panel flat on protected surface.
Insert dowels into side panels as marked, then attach to back panel using cam locks.
Attach top and bottom panels to side panels using remaining dowels and cam locks.
Tighten all cam locks clockwise until firm (do not overtighten).
Attach mounting brackets to back panel using provided screws.
Install adjustable shelf supports at desired heights.
Attach door hinges to side panel using hinge screws, then hang door.
Adjust door alignment via hinge screws if needed for smooth closing.

Tip: Ensure all cam locks are fully tightened before mounting.

Wall Mounting Installation

Proper mounting is critical for safety.

Locate wall studs using stud finder; mark positions with pencil.
Hold cabinet against wall at desired height (recommended 60 inches from floor to bottom).
Use level to ensure cabinet is horizontal; mark screw holes through bracket slots.
Drill pilot holes at marked points into studs or drywall (for anchors).
If using drywall anchors, insert anchors into holes and tap gently with hammer.
Lift cabinet and align brackets with holes; insert screws and tighten securely.
Test stability by gently pulling forward; cabinet should not move.

CAUTION! Mount only to solid structures. Do not rely on drywall alone without anchors.

Adjusting Shelves

Shelves are adjustable for flexible storage.

Remove shelves by lifting slightly and pulling forward.
Reposition shelf supports by pushing upward and out of holes, then inserting at new desired height.
Place shelf on supports, ensuring it rests evenly on all four corners.
Load items evenly; avoid placing heavy items near front edge.

Note: Maximum load per shelf: 22 lbs (10 kg). Distribute weight evenly.

Care & Maintenance

Clean regularly to maintain appearance.

Wipe exterior with damp cloth and mild detergent; dry immediately.
Clean glass door with glass cleaner and soft cloth; avoid abrasive materials.
Do not use harsh chemicals, solvents, or abrasive cleaners on surfaces.
Tighten screws and hinges periodically if loosening occurs.

CAUTION! Avoid excessive water; do not soak or immerse cabinet.

Specifications

Model: RUNMARÖ 205.513.12
Color: White
Dimensions: 23.5" W x 11.5" D x 30.5" H (60 x 29 x 77.5 cm)
Material: Particleboard, foil, ABS plastic, tempered glass
Door: Tempered glass with integrated handle
Shelf Capacity: 22 lbs (10 kg) per shelf
Weight: 28.5 lbs (13 kg)
Mounting: Wall-mounted; requires studs or anchors
Assembly: Required; tools not included

Troubleshooting

Issue	Possible Cause	Solution
Cabinet wobbles	Loose screws or improper mounting	Tighten all screws; ensure mounted into studs or secure anchors.
Door not closing properly	Misaligned hinges	Loosen hinge screws slightly, adjust door position, retighten.
Shelf not level	Uneven shelf supports	Remove shelf and reposition supports at same height on both sides.
Cam locks not holding	Not fully tightened or dowels not inserted	Check dowel insertion; turn cam locks clockwise until firm.
Difficulty mounting to wall	No studs found	Use appropriate drywall anchors rated for cabinet weight; follow anchor instructions.

Tip: If parts are missing or damaged, contact IKEA support for replacements.

Warranty & Support

IKEA limited warranty applies; see IKEA terms for details. For missing parts or assembly help:

Visit IKEA store or website: www.ikea.com
Contact customer support: 1-888-888-4532
Provide model number (205.513.12) and proof of purchase.

Note: Warranty does not cover improper installation, misuse, or accidental damage.