IKEA RINNEN 493.159.61 Water Trap instructions manual

The IKEA RINNEN 493.159.61 Water Trap is a plumbing component designed to prevent foul odors from entering the living space by maintaining a water seal in the drainage system. It is typically installed under sinks, washbasins, showers, and other sanitary fixtures. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Maintenance 8. Accessibility Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Water trap body, sealing gaskets, connection nuts, overflow outlet, and cleaning eye.

Feature	Description
Material	Durable plastic (PP or ABS) resistant to corrosion and chemicals
Water Seal	Maintains a water barrier to prevent sewer gases from entering
Connection Size	Standard 40mm (1.5 inch) outlet; 32mm/40mm inlet options
Cleaning Eye	Provides access for clearing blockages without disassembly
Overflow Outlet	Optional connection for sink overflow pipe
Adjustable Height	Some models allow height adjustment for flexible installation
Sealing System	Rubber gaskets ensure watertight connections
Compact Design	Saves space under the sink or basin
Color	Typically white to match standard plumbing fixtures
Compatibility	Designed for IKEA RINNEN series washbasins and sinks

Installation

Unpack and inspect contents. Ensure all parts are present and undamaged.

Position the trap: Align the water trap between the basin waste outlet and the wall drainage pipe.
Connect to basin: Attach the upper section to the basin waste outlet using the provided nut and washer.
Connect to drainage: Attach the lower section to the wall drainage pipe, ensuring a secure fit.
Tighten connections: Hand-tighten all nuts; avoid over-tightening to prevent damage.
Check alignment: Ensure the trap is vertical and not under stress from pipe misalignment.

WARNING! Ensure the water trap is installed correctly to prevent leaks and gas escape. Do not use excessive force.

First-Time Setup

After installation, perform initial checks to ensure proper function.

Test for leaks: Slowly fill the basin with water and check all connections for drips.
Check water seal: After draining, verify that the trap retains water to form a seal.
Clear debris: Run water to flush out any installation debris from the trap.
Secure mounting: Ensure the trap is properly supported and not hanging from pipes.

CAUTION! Always test the installation before regular use to prevent water damage.

Specifications

Model: RINNEN 493.159.61
Type: Bottle-type water trap (S-trap/P-trap variant)
Inlet Diameter: 32 mm or 40 mm (as specified)
Outlet Diameter: 40 mm (standard)
Material: Polypropylene (PP) or Acrylonitrile Butadiene Styrene (ABS)
Color: White
Water Seal Depth: Minimum 50 mm as per plumbing standards
Operating Temperature: Suitable for standard wastewater temperatures (0-60°C)
Standards: Complies with relevant EU plumbing and sanitation standards

Controls and Settings

The water trap is a passive component with no electronic controls. "Settings" refer to installation adjustments.

Adjustable Height: Some models feature telescopic sections that can be extended or retracted to match pipe distances. Loosen the locking nut, adjust length, and re-tighten.

Orientation: Can be installed as P-trap (outlet horizontal) or S-trap (outlet vertical) depending on drainage configuration.

Cleaning Eye: The removable plug allows access for maintenance.

Connecting Devices

Connects the sanitary fixture (sink, basin) to the building drainage system.

Ensure all connections are clean and free from old sealant or debris.
Use appropriate washers and gaskets provided; do not substitute with incompatible materials.
For threaded connections, hand-tighten first, then use a wrench for a quarter turn maximum.
If connecting to an older pipe, ensure compatibility of diameters; use adapters if necessary.

Tip: Apply a small amount of silicone grease to rubber seals for easier assembly and better sealing.

Maintenance

Regular maintenance prevents blockages and ensures the water seal remains effective.

Monthly check: Visually inspect for leaks or cracks.
Cleaning: Remove the cleaning eye plug periodically to clear hair and debris.
Deep clean: Disassemble the trap every 6-12 months. Soak parts in warm water with mild detergent.
Seal check: If odors are noticed, the water seal may have evaporated. Run water to refill the trap.
Winter care: In unheated spaces, ensure the trap does not freeze. Use insulation if necessary.

WARNING! Never use chemical drain cleaners as they can damage plastic components. Use mechanical methods (plunger, drain snake) for blockages.

Accessibility Features

The design prioritizes ease of installation and maintenance.

Tool-Free Access: The cleaning eye can often be removed by hand for quick access.

Modular Design: Simple disassembly without specialized tools.

Clear Instructions: Pictograms on packaging assist with installation steps.

Care & Cleaning

Use only mild, non-abrasive cleaners. Avoid harsh chemicals, scouring pads, or high-pressure water jets.

CAUTION! Do not expose to direct flame or temperatures above 80°C. Do not use solvents like acetone or paint thinners.

Regulatory Information

This product conforms to EU construction product regulations and relevant national plumbing standards. It is designed for use in residential drainage systems. The material is recyclable (check local recycling codes). For IKEA warranty and support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Foul odor from drain	Water seal evaporated or broken	Run water to refill trap. Check for leaks or incorrect slope.
Water leaking from connections	Loose nut or damaged seal	Tighten connection. Replace worn washer or gasket.
Slow drainage	Partial blockage in trap	Remove cleaning eye to clear debris. Use a drain snake if necessary.
Gurgling sounds	Ventilation issue or blockage	Ensure vent pipe is clear. Check for obstructions in the trap.
Trap is dry in unused fixture	Evaporation over time	Pour a cup of water down the drain monthly to maintain seal.
Crack or damage visible	Physical impact or material fatigue	Replace the entire water trap. Do not attempt to repair cracks.

Replacement: If troubleshooting fails, replace the water trap with an identical IKEA model.

Service: For installation questions or parts, contact IKEA customer service or visit the IKEA website.