IKEA RANARP 103.909.56 Lighting instructions manual

The IKEA RANARP 103.909.56 is a stylish, adjustable LED work lamp designed for desks and workspaces. It features a flexible gooseneck arm, energy-efficient LED light source with adjustable brightness, a sturdy clamp base for secure attachment, and a classic industrial design. Below are key sections for safety, features, installation, setup, operation, care, and troubleshooting.

Features at a Glance

Key components: Adjustable gooseneck arm, LED light head, On/Off switch with dimmer, Clamp base with protective pads, Power cord with plug.

Installation & Mounting

Unpack and inspect all parts. Ensure you have a stable surface for mounting.

1. Position the clamp: Open the clamp by turning the screw counterclockwise.
2. Attach to surface: Place clamp on edge of desk or shelf (max thickness 2.4" / 60mm).
3. Secure the clamp: Turn the screw clockwise until the lamp is firmly held. Do not overtighten.
4. Adjust the arm: Gently bend the gooseneck to desired position.
5. Plug in: Connect the power cord to a standard 120V AC outlet.

WARNING! Ensure the clamp is securely fastened to prevent the lamp from falling. Do not mount on unstable or slippery surfaces.

First-Time Setup

After mounting, configure your lamp for optimal use.

1. Power on: Rotate the dimmer switch clockwise until you hear a click. The light will turn on at minimum brightness.
2. Adjust brightness: Continue rotating clockwise to increase light intensity to your preferred level.
3. Position the light: Bend the gooseneck arm and tilt the light head to direct light exactly where needed.
4. Test stability: Gently nudge the lamp to ensure the clamp is secure.

CAUTION! When adjusting the gooseneck, support the arm with your other hand. Do not bend it forcefully beyond its natural range.

Specifications

• Product Name: RANARP Work lamp
• Article Number: 103.909.56
• Light Source: Integrated LED, non-replaceable
• Light Output: Adjustable, 300-600 lumens (approx.)
• Color Temperature: 2700K (Warm white)
• Power Consumption: 4.5W (max)
• Power Supply: 120V AC, 60Hz
• Cord Length: 59" (150 cm)
• Clamp Capacity: Up to 2.4" (60 mm) thickness
• Material: Steel, Aluminum, Plastic
• Dimensions: Height: 19.7" (50 cm), Base depth: 5.9" (15 cm)

Controls and Operation

The lamp is controlled via a single integrated rotary dial on the power cord or base (model dependent).

Operation:

1. Off: Dial turned fully counterclockwise (click at minimum position).
2. On & Dimming: Rotate clockwise to turn on and increase brightness smoothly.
3. Maximum Brightness: Dial turned fully clockwise.

Positioning: The gooseneck arm can be bent and shaped. The light head can be tilted up/down. Avoid sharp bends in the arm.

Light Adjustment & Positioning

For optimal task lighting, follow these guidelines:

1. Position the lamp so the light comes from the side opposite your writing hand to avoid shadows.
2. Place the lamp 12-18 inches from your work surface.
3. Angle the light head to illuminate the task directly, not your eyes.
4. Use the flexible arm to route the light over or around obstacles.

Tip: For reading, position the light behind your shoulder. For detailed work, position it directly above the task.

Energy & Brightness Settings

The integrated LED is designed for efficiency and long life.

• Use lower brightness settings for ambient lighting or prolonged use to save energy.
• Higher brightness is ideal for focused tasks like reading small print or crafting.
• The LED produces minimal heat, making it safe for extended use.
• Estimated LED lifespan: 25,000 hours.

Note: The LED light source is not user-replaceable. If it fails, the entire lamp unit will need service.

Safety Information

To ensure safe operation, please follow these instructions:

• Electrical Safety: Plug into a properly grounded outlet. Do not use with extension cords as a permanent solution.
• Placement: Keep the lamp away from water, humid areas, and heat sources.
• Children: This is not a toy. Keep out of reach of young children.
• Maintenance: Unplug the lamp before any cleaning or maintenance.
• Inspection: Regularly check the cord, plug, and clamp for any signs of damage.

WARNING! Do not attempt to disassemble the lamp. There are no user-serviceable parts inside.

Care & Cleaning

Unplug the lamp from the outlet before cleaning.

1. Exterior: Wipe with a soft, dry or slightly damp cloth. Do not use abrasive cleaners or solvents.
2. Gooseneck & Shade: Dust with a soft brush or dry cloth.
3. Clamp & Base: Clean with a damp cloth if necessary. Ensure all parts are dry before plugging back in.

CAUTION! Never immerse the lamp, cord, or plug in water or other liquids. Do not use spray cleaners directly on the product.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included with your purchase or available at IKEA stores.

Support: For assembly help, spare parts, or other inquiries:

• Visit: www.ikea.com
• Contact your local IKEA store.
• Refer to the product page for the RANARP lamp (103.909.56).

This product complies with applicable electrical safety standards.

Troubleshooting

Note: The integrated LED is not designed to be replaced. If the LED fails, please contact IKEA.