IKEA RANARP 103.313.92 Work Lamp instructions manual

The IKEA RANARP 103.313.92 is a classic-style work lamp with an adjustable arm and head, designed for focused task lighting. It features a metal construction, a pull-chain switch, an E26/E27 socket for bulbs up to 60W (not included), and a clamp base for versatile mounting. Below are key sections for safety, assembly, installation, operation, care, and troubleshooting.

1. Features at a Glance 2. Parts & Tools Required 3. Assembly Instructions 4. Installation & Mounting 5. Specifications 6. Operation & Controls 7. Adjusting the Lamp 8. Bulb Replacement 9. Care & Cleaning 10. Safety Information 11. Troubleshooting

Features at a Glance

Key components: Adjustable metal arm and shade, Clamp base, Pull-chain switch, E26/E27 bulb socket.

Feature	Description
Adjustable arm	Spring-balanced arm for precise positioning
Rotatable shade	Shade rotates to direct light where needed
Clamp base	Securely attaches to desks, shelves, or tables up to 2.4" thick
Pull-chain switch	On/off control located on the lamp head
Bulb socket	Standard E26/E27 base for bulbs up to 60W max
Construction	Powder-coated metal for durability
Cable length	Approx. 5.9 ft (1.8 m) power cord
Finish	Black or white finish options

Parts & Tools Required

Inspect all parts from the package before assembly.

Lamp Parts: Clamp base, Arm assembly, Lamp head/shade, Knobs and screws (pre-attached or included).
Required Tools: No tools required for basic assembly. A screwdriver may be needed to tighten the clamp if necessary.
Not Included: Light bulb (E26/E27, max 60W).

WARNING! Ensure you have all parts. Do not attempt assembly if parts are missing or damaged.

Assembly Instructions

Follow these steps to assemble your RANARP work lamp.

Attach the arm to the clamp base: Insert the arm's mounting post into the socket on the clamp base. Tighten the locking knob securely by hand.
Attach the lamp head to the arm: Align the head's connector with the end of the arm. Push together until it clicks or seats firmly. Tighten any adjustment knobs by hand to secure.
Check all joints: Ensure all knobs are tight enough to hold positions but allow adjustment when needed.
Insert bulb: Screw an appropriate bulb (E26/E27, max 60W) into the socket. Do not exceed wattage.

CAUTION! Assemble on a soft surface to avoid scratching. Ensure all connections are secure before use.

Installation & Mounting

Clamp Mounting: Open the clamp by turning the screw counterclockwise. Position on edge of desk/shelf (max thickness 2.4"/60mm). Tighten screw firmly by hand or with screwdriver until secure.
Surface: Ensure mounting surface is stable, solid, and can support the lamp's weight.
Power: Plug the cord into a standard 120V AC outlet. Keep cord away from heat and sharp edges.

Tip: For optimal stability, clamp to the center of the surface edge, not a corner.

Specifications

Product Name: RANARP Work lamp
Article Number: 103.313.92
Dimensions: Height: 19.7" (50 cm), Width: 9.8" (25 cm), Depth: 31.5" (80 cm) when fully extended.
Max. Bulb Wattage: 60W (E26/E27 base).
Voltage: 120V AC, 60Hz.
Cord Length: 5.9 ft (1.8 m).
Material: Steel, Powder coating.
Weight: Approx. 3.3 lbs (1.5 kg).

Operation & Controls

Operating the lamp is simple via the pull-chain switch.

On/Off: Pull the chain hanging from the lamp head once to turn on. Pull again to turn off.

Adjustment: The lamp arm and head are adjustable. Loosen the knobs at the joints, position as desired, then re-tighten knobs to lock in place.

Note: The pull-chain is the only control; there is no dimmer.

Adjusting the Lamp

The lamp offers flexible positioning for task lighting.

Arm Height & Reach: Loosen the main arm knob. Raise, lower, or extend the arm. Tighten knob.
Head Tilt & Rotation: Loosen the head joint knob. Tilt shade up/down and rotate side-to-side. Tighten knob.
Fine-tuning: Small adjustments can be made without fully loosening knobs due to spring tension.

WARNING! Do not force the arm or head beyond its natural range of motion.

Bulb Replacement

Always turn off and unplug the lamp before replacing the bulb.

Allow bulb to cool completely if recently on.
Grip the bulb firmly and turn counterclockwise to remove.
Insert new E26/E27 bulb (max 60W). Screw clockwise until snug. Do not overtighten.
Plug in and test with pull-chain.

CAUTION! Use only bulbs with the specified base and wattage. LED or CFL bulbs recommended for energy efficiency and lower heat.

Care & Cleaning

Unplug lamp before cleaning.

Use a soft, dry cloth to dust the metal surfaces.
For tougher marks, dampen cloth slightly with water. Wipe dry immediately.
Do not use abrasive cleaners, solvents, or chemicals.
Do not immerse any part of the lamp in water.

CAUTION! Never spray liquids directly onto the lamp. Keep electrical parts dry.

Safety Information

Important safety instructions to prevent fire, electric shock, or injury.

This lamp is for indoor use only.
Use only with a 120V AC power outlet.
Do not exceed maximum bulb wattage (60W).
Ensure the clamp is securely fastened to a stable surface.
Keep cord away from heated surfaces and foot traffic.
Do not use if cord or plug is damaged.
Not intended for use with dimmer switches.
Keep out of reach of young children.

Complies with relevant safety standards.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Bulb burnt out; not plugged in; loose bulb	Replace bulb; ensure plug is in outlet; tighten bulb in socket.
Lamp is unstable or falls	Clamp not tight enough; surface too thick	Tighten clamp screw; ensure surface is within 2.4" thickness limit.
Arm does not hold position	Joint knobs are loose	Tighten the knobs at the arm and head joints.
Lamp flickers	Loose bulb; faulty bulb; poor socket contact	Turn off, reseat bulb; try a different bulb.
Pull-chain feels stiff or breaks	Mechanical defect; overuse	Discontinue use. Contact IKEA for support.

Service: For missing parts or product support, contact IKEA customer service at 1-800-434-4532 or visit www.IKEA-usa.com.