IKEA RÅVAROR 204.545.04 Shelf instructions manual
The IKEA RÅVAROR 204.545.04 is a wall-mounted shelf unit designed for storage and display. Constructed from particleboard with a white foil finish, it features a clean, minimalist design suitable for various rooms. Below are key sections for safety, parts list, tools required, assembly instructions, mounting guidelines, care, and warranty information.
Parts & Hardware Included
Before assembly, verify all parts are present. Key components: Shelf boards, brackets, wall anchors, screws.
| Part Number | Description | Quantity |
|---|
| 101 | Shelf board (main) | 1 |
| 102 | Shelf board (secondary) | 1 |
| 201 | Metal bracket (L-shaped) | 2 |
| 301 | Wall screw | 4 |
| 302 | Plastic wall anchor | 4 |
| 303 | Screw for bracket-to-shelf | 8 |
| — | Assembly instruction manual | 1 |
Tools Required
Not included; you will need:
- Phillips screwdriver (or cordless drill with Phillips bit)
- Pencil
- Level
- Measuring tape
- Hammer (for installing wall anchors)
- Stud finder (recommended)
Safety Instructions
WARNING! Failure to follow these instructions can result in serious injury or damage.
- Two-person assembly: Some steps require two people to safely handle parts.
- Wall mounting: Always mount to wall studs or use appropriate anchors for your wall type (drywall, plaster, concrete).
- Weight limit: Do not exceed maximum load capacity (see section 7).
- Child safety: Do not allow children to climb on or hang from the shelf.
- Tool safety: Use tools as intended; keep away from children.
CAUTION! Ensure the shelf is securely mounted before placing items on it.
Assembly Steps
Follow steps in order. Allow approximately 30 minutes for assembly.
- Prepare workspace: Clear area; lay out all parts and hardware.
- Attach brackets to shelves:
- Align bracket (201) with pre-drilled holes on underside of shelf board (101).
- Secure using screws (303). Repeat for second bracket on same shelf.
- Repeat for secondary shelf board (102) if applicable.
- Check alignment: Ensure brackets are parallel and flush with shelf edges.
- Do not fully tighten: Leave screws slightly loose for final adjustment during wall mounting.
Tip: Do not overtighten screws, as this may damage the particleboard.
Wall Mounting
Most critical step; ensures safety and stability.
- Locate studs: Use stud finder to locate wall studs. Mark center with pencil.
- Plan position: Decide shelf height and level. Use measuring tape and level to mark bracket mounting points on wall.
- Drill pilot holes: At marked points, drill holes slightly smaller than wall anchors (302). For stud mounting, drill directly into stud.
- Insert anchors: For drywall without stud, tap plastic anchors (302) into holes with hammer until flush.
- Mount brackets:
- Have one person hold shelf with brackets against wall, aligned with holes.
- Insert wall screws (301) through bracket holes into anchors/studs.
- Tighten securely but do not strip.
- Final tightening: Once shelf is mounted and level, fully tighten all bracket-to-shelf screws (303).
WARNING! If you are unsure about wall type or mounting, consult a professional.
Weight Capacity & Limitations
- Maximum load: 25 lbs (11.3 kg) evenly distributed per shelf.
- Wall type: Must be mounted to solid wall (stud, concrete, brick). Not suitable for hollow doors or thin partitions.
- Environmental: For indoor use only. Avoid high humidity (e.g., bathrooms) unless specified.
- Dimensions: 31.5" L x 7.875" D x 2.75" H (80 cm x 20 cm x 7 cm).
- Material: Particleboard, White foil
Care & Maintenance
Unload shelf before any maintenance.
- Cleaning: Wipe with dry or slightly damp cloth. Do not use abrasive cleaners, chemicals, or excessive water.
- Inspection: Periodically check tightness of screws and brackets. Retighten if loose.
- Relocation: To move, remove all items, unscrew from wall, and remount following wall mounting instructions.
CAUTION! Do not use shelf as a step ladder or seat.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|
| Shelf not level | Uneven wall or incorrect mounting | Loosen screws, adjust with level, retighten. |
| Brackets feel loose | Screws not fully tightened | Tighten all screws (wall and bracket). |
| Shelf sags under weight | Exceeded weight limit or improper mounting | Reduce load; ensure mounted to studs. |
| Difficulty drilling into wall | Wrong drill bit or hard wall material | Use appropriate bit for wall (masonry bit for concrete). |
| Missing part | Packaging error | Contact IKEA customer service with product number. |
Warranty & Support
IKEA limited warranty applies. See IKEA terms or www.IKEA.com for details.
Support: For missing parts, assembly questions, or warranty claims:
- Visit: www.IKEA.com
- Contact your local IKEA store
- Refer to product number: 204.545.04
Recycling: Dispose of packaging responsibly. Product is recyclable where facilities exist.
IKEA RÅVAROR 204.545.04 Shelf instructions manual © - All Rights Reserved 2025