IKEA POÄNG 093.360.36 Ottoman instructions manual

The IKEA POÄNG 093.360.36 Ottoman is a complementary footrest designed to match the iconic POÄNG armchair. It features a curved birch veneer frame, steel tensioning system for comfort, removable fabric or leather cover (depending on model), and a lightweight yet sturdy construction for easy movement. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Tools Included 2. Safety Information 3. Step-by-Step Assembly 4. Care & Maintenance 5. Specifications 6. Cover Removal & Cleaning 7. Warranty & Support 8. Troubleshooting

Parts & Tools Included

All parts needed for assembly are included in the package. Please verify contents before starting.

Part Number	Description	Quantity
100001	Curved frame (left side)	1
100002	Curved frame (right side)	1
100003	Front crossbar	1
100004	Rear crossbar	1
100005	Steel tension springs	2
100006	Fabric/Leather cover	1
100007	Plastic plugs	4
100008	Allen key	1
100009	Screws (pre-attached)	8

Safety Information

Read all instructions before assembly. Keep children and pets away during assembly.

Assemble on a soft, clean surface to avoid scratching parts.
Use only the provided Allen key; do not overtighten screws.
Ensure all connections are secure before use.
Weight limit: 220 lbs (100 kg). Do not stand or jump on the ottoman.

WARNING! Choking hazard: Small parts included. Not suitable for children under 3 years. Frame may have sharp edges; handle with care.

Step-by-Step Assembly

Estimated assembly time: 15-20 minutes. Follow steps in order.

Step 1: Lay out all parts as shown in the diagram. Identify left and right frame pieces.
Step 2: Connect the front crossbar (100003) to the left and right frames using the pre-attached screws. Hand-tighten first.
Step 3: Attach the rear crossbar (100004) in the same manner, ensuring the frame forms a rectangular shape.
Step 4: Insert the two steel tension springs (100005) into the designated slots on the inner frame. They should snap into place.
Step 5: Using the Allen key, fully tighten all eight screws (two per corner) until firm. Do not strip the threads.
Step 6: Place the fabric/leather cover (100006) over the frame, aligning the seams with the corners. Ensure it sits evenly.
Step 7: Insert the four plastic plugs (100007) into the holes at the bottom of the frame to cover screw heads.

Tip: If the cover feels tight, gently stretch it over the frame corners. It will relax with use.

Care & Maintenance

Frame: Wipe with a dry or slightly damp cloth. Do not use abrasive cleaners.
Cover: Regular vacuuming recommended. See Section 7 for detailed cleaning based on material.
Moving: Lift, do not drag, to protect floor surfaces and frame joints.
Storage: Store in a dry place. Avoid prolonged direct sunlight to prevent fading.

Specifications

Model: POÄNG Ottoman 093.360.36
Dimensions (Assembled): 22" L x 22" W x 16" H (56cm x 56cm x 41cm)
Frame Material: Birch veneer, steel tension springs
Cover Material: Removable fabric or leather (varies by color option)
Weight Capacity: 220 lbs (100 kg)
Product Weight: 11 lbs (5 kg)
Packaging: Flat-pack, recyclable cardboard

Cover Removal & Cleaning

The cover is removable for easy cleaning. Check the label inside the cover for material-specific codes.

Turn the ottoman upside down on a clean surface.
Gently pull the cover upwards and off the frame, starting from one corner.
For Fabric Covers (Code W): Machine wash cold, gentle cycle. Do not bleach. Tumble dry low or air dry.
For Leather Covers (Code L): Wipe with a damp cloth and mild soap. Condition with IKEA leather care product. Do not machine wash.
Allow cover to dry completely before reassembling onto the frame.

CAUTION! Always follow the care label instructions. Improper cleaning may damage the cover.

Warranty & Support

This product is covered by IKEA's limited warranty. Refer to the IKEA warranty booklet included in the package or available at www.ikea.com.

For missing parts or assembly help: Visit the IKEA store where purchased or contact IKEA Customer Support at 1-888-888-4532.

Online Resources: Assembly video and guide available at www.ikea.com/us/en/customer-service/product-support

Troubleshooting

Issue	Possible Cause	Solution
Frame feels wobbly	Screws not fully tightened	Check and tighten all eight screws with the Allen key.
Cover is uneven or loose	Not properly aligned during assembly	Remove cover and reposition, ensuring seams match frame corners.
Squeaking noise when used	Wood parts rubbing; springs not seated	Ensure tension springs are fully snapped into slots. Tighten screws.
Plastic plugs won't stay in	Holes may be obstructed	Clear any debris from the holes and press plugs firmly until they click.
Missing part	Part left in packaging or not included	Check all packaging materials. Contact IKEA for replacement parts.

Note: Do not use glue or adhesives on any part of the ottoman, as this voids the warranty.