IKEA PAX 094.322.69 Door Frame instructions manual

The IKEA PAX 094.322.69 is a door frame component designed for the PAX wardrobe system. It is used to create a finished opening for sliding or hinged doors, providing structural support and a clean aesthetic. This manual covers safety precautions, parts identification, step-by-step assembly instructions, mounting guidelines, adjustment procedures, and maintenance tips for proper installation and use.

Parts Included

Verify all components are present before starting assembly.

Tools Required

Not included. You will need to provide the following:

• Phillips screwdriver (size #2)
• Hex key (Allen wrench, 4mm) - often included with PAX system
• Hammer
• Level
• Pencil
• Tape measure
• Drill (for wall mounting, if applicable)
• Wall plugs & screws appropriate for your wall type

Safety Information

WARNING! Failure to follow these instructions can result in serious injury or damage.

1. Two-Person Job: The frame is large and awkward. Always assemble and lift with at least two people.
2. Stable Surface: Assemble on a clean, flat, protected surface to prevent scratches.
3. Secure Mounting: Always secure the frame to the wall using the provided brackets to prevent tipping.
4. Check Wall Type: Ensure you use correct fixings for your wall (solid wall, drywall, stud).
5. Keep Away from Children: Small parts are a choking hazard. Keep assembly area clear during and after build.

CAUTION! Do not overtighten screws or cam locks, as this may strip the particleboard.

Assembly Instructions

Follow these steps in order. Do not fully tighten connectors until all parts are joined.

1. Prepare Parts: Lay all parts on the floor with the finished sides facing down.
2. Attach Top Rail Connectors: Insert the two Top Rail Connectors (102.345.01) into the pre-drilled holes at the top of the door frame upright. Secure with provided Cam Lock Screws (105.678.04). Turn cam locks 90° clockwise to lock.
3. Attach Bottom Guide Plate: Slide the Bottom Guide Plate (103.456.02) into the slot at the base of the frame. Tap gently with a hammer if needed. Ensure it is flush and straight.
4. Join with Other Frame Section: If building a double door opening, align a second PAX frame section. Connect them using the Top Rail Connectors and corresponding hardware. Tighten all connections.
5. Insert Cover Caps: Press the small Cover Caps (106.789.05) into the visible cam lock holes to conceal them.

Tip: Assemble the frame close to its final location to avoid moving the heavy structure long distances.

Mounting to Wall & Wardrobe

The frame must be securely attached to the wall for stability.

1. Position Frame: With help, lift the assembled frame into its final position against the wall and adjacent PAX wardrobe units.
2. Check for Level & Plumb: Use a level to ensure the frame is perfectly vertical (plumb) and the top rail is horizontal. Shim the bottom if the floor is uneven.
3. Mark Bracket Locations: Mark the wall through the holes in the four Wall Attachment Brackets (104.567.03).
4. Drill Pilot Holes: Remove the frame. Drill pilot holes at the marked locations using a drill bit suitable for your wall plugs.
5. Secure Frame: Reposition the frame. Insert screws through the brackets into the wall plugs. Tighten securely, but do not pull the frame out of alignment.
6. Attach to Wardrobe: If connecting to existing PAX units, use the provided connectors to fix the frame to the side panel of the wardrobe for a seamless look.

Door Installation

Instructions for attaching sliding or hinged doors to the frame.

1. For Sliding Doors:
   • Lift the first door panel and hook the top wheels onto the top track of the frame.
   • Let the door hang. Adjust the top wheels so the door is level and parallel to the frame.
   • Insert the bottom guide pin on the door into the Bottom Guide Plate on the frame.
   • Repeat for the second door.
   • Adjust the height and tilt using the screws on the top wheel assemblies.
2. For Hinged Doors:
   • Attach the hinges to the door first, following the door's specific instructions.
   • With help holding the door, screw the hinge plates directly into the pre-drilled holes on the side of the PAX door frame.
   • Start with the top and bottom hinges, check alignment, then attach the middle hinge(s).
3. Final Check: Open and close doors several times. Ensure they move smoothly without catching or dragging.

Adjustments & Alignment

Common adjustments for proper door operation.

Care & Maintenance

To ensure long life and proper function.

• Cleaning: Wipe frame with a soft, damp cloth. Use mild soap if needed. Dry immediately. Do not use abrasive cleaners, scouring pads, or chemical solvents.
• Hardware Check: Periodically (every 6-12 months) check that all screws, cam locks, and wall brackets are tight.
• Track Cleaning: For sliding doors, vacuum the bottom track and wipe the top track with a dry cloth to remove dust and debris.
• Wheel Lubrication: If sliding doors become stiff, apply a small amount of silicone-based lubricant (not oil) to the wheel axles and top track.
• Avoid Moisture: Protect from prolonged exposure to high humidity or direct water contact.

Technical Specifications

• Article Number: 094.322.69
• Type: PAX Door Frame Upright
• Material: Particleboard, Fiberboard, Plastic, Steel
• Finish: White, Foil
• Height: 236.4 cm (93 1/8")
• Width: 6.6 cm (2 5/8")
• Depth: 6.3 cm (2 1/2")
• Weight: 8.5 kg (18.7 lb)
• Max Door Weight: Supports PAX sliding doors up to 40 kg (88 lb) per panel.
• System Compatibility: Designed for use with PAX wardrobe frames, interiors, and doors.

Warranty & Support

This IKEA product is covered by the IKEA limited warranty. Refer to the IKEA warranty document for full terms and conditions.

IKEA Customer Support:
Website: www.ikea.com
Phone: 1-888-888-4532 (IKEA-USA)
For spare parts: Use the article number (094.322.69) when contacting support or visiting the IKEA store Spare Parts department.

Important: Retain your receipt as proof of purchase. The warranty does not cover damage caused by incorrect assembly, modification, or failure to follow assembly and mounting instructions.

Troubleshooting

Note: If problems persist, contact IKEA customer support for assistance. Do not use the wardrobe if it is unstable.