IKEA PAX 091.248.26 Wardrobe Frame instructions manual

The IKEA PAX 091.248.26 is a versatile wardrobe frame system designed for customizable storage solutions. It features a modular design with adjustable shelves, rails, and interior fittings, allowing you to configure the space to suit your needs. The frame is constructed from particleboard with a white foil finish, requiring assembly. Below are key sections for safety, parts list, assembly instructions, installation, configuration, care, and troubleshooting.

1. Parts and Hardware 2. Safety Information 3. Assembly Instructions 4. Installation and Mounting 5. Interior Configuration 6. Door Installation (Optional) 7. Care and Maintenance 8. Weight Limits and Specifications 9. Troubleshooting 10. Warranty and Support

Parts and Hardware

Before assembly, verify all parts are present. Key components: Wardrobe frame panels, top panel, bottom panel, back panel, screws, cam locks, dowels, wall attachment fittings.

Part Description	Quantity	Hardware Included
Side panel (left)	1	Pre-drilled holes for shelves/rails
Side panel (right)	1	Pre-drilled holes for shelves/rails
Top panel	1	Reinforced for stability
Bottom panel	1	Adjustable feet included
Back panel (fiberboard)	1	Pre-cut for mounting
Cam locks	8	For panel connections
Screws (various sizes)	As per pack	For hardware and wall attachment
Dowels	10	For alignment during assembly
Wall attachment fittings	2	To secure wardrobe to wall

Safety Information

Read all instructions before assembly. Ensure a safe workspace.

Tip-over prevention: This wardrobe must be securely attached to the wall using the provided fittings to prevent tipping, especially if children are present.
Lifting: The panels are heavy; use two people for lifting and assembly to avoid injury.
Tools: Use only the recommended tools (Phillips screwdriver, hammer).
Surface: Assemble on a soft, clean surface to avoid scratches.

WARNING! Failure to secure the wardrobe to the wall can result in serious injury or death from tipping.

Assembly Instructions

Follow steps in order. Allow approximately 60-90 minutes for assembly.

Prepare: Unpack all parts and hardware. Identify each component using the included guide.
Connect side and bottom panels: Insert dowels into side panels. Align with holes in the bottom panel and secure using cam locks.
Attach top panel: Lift and align the top panel with the side panels. Secure with dowels and cam locks.
Install back panel: Lay the frame face down on a protected surface. Position the back panel and secure it with screws into the pre-drilled holes along the perimeter.
Attach adjustable feet: Screw the adjustable feet into the bottom of the bottom panel.
Stand the frame upright: Carefully lift the assembled frame with help and place it in its desired location.

Tip: Do not fully tighten cam locks until all panels are aligned.

Installation and Mounting

Securing the wardrobe to the wall is mandatory.

Position the wardrobe in its final location, ensuring it is level using the adjustable feet.
Locate the solid wall stud(s) behind the intended position.
Use the provided wall attachment fittings and screws. Attach the fittings to the top rear of the wardrobe frame as indicated in the pre-drilled holes.
Drive screws through the fittings and into the wall stud(s). Ensure they are tight and secure.
Check stability by gently trying to tip the wardrobe forward. It should not move.

CAUTION! If you cannot locate a stud, use appropriate wall anchors suitable for the wall material and the weight of the fully loaded wardrobe.

Interior Configuration

The PAX system is highly customizable. Use IKEA KOMPLEMENT interior fittings.

Shelves: Adjustable height. Place shelf supports into desired holes on side panels and rest shelf on top.
Clothing rail: For hanging clothes. Install rail supports and slide the rail into place.
Drawers: Requires separate KOMPLEMENT drawer frames. Follow specific drawer assembly instructions.
Baskets/Shoe racks: Various accessories can be mounted using the standard hole system.

Note: Distribute weight evenly. Heavier items should be placed on lower shelves or hanging areas.

Door Installation (Optional)

Doors are sold separately. Ensure you have the correct size for the PAX 091.248.26 frame.

Attach hinge plates to the door panel according to the door's instructions.
With help, hold the door against the frame, aligning the hinges with the pre-drilled holes on the side panel.
Insert and tighten the screws to secure the hinges to the frame.
Adjust the door height and alignment using the adjustment screws on the hinges.
Install door handles as desired.

Tip: Install doors last, after all interior fittings are in place.

Care and Maintenance

Clean with a damp cloth wrung out in mild soapy water. Wipe dry immediately.

Avoid: Abrasive cleaners, scouring pads, or harsh chemicals.
Protect: Keep away from direct heat sources and excessive moisture.
Check: Periodically check and tighten wall attachment screws and cam locks.

CAUTION! Do not overload shelves or hang excessive weight on the clothing rail.

Weight Limits and Specifications

Frame Dimensions (HxWxD): 2012 x 1000 x 580 mm (79 1/8" x 39 3/8" x 22 7/8").
Material: Particleboard, Fiberboard, Foil, Plastic edging.
Max Load per Shelf: 15 kg (33 lb) evenly distributed.
Max Load per Clothing Rail: 30 kg (66 lb).
Total Recommended Load: Do not exceed 80 kg (176 lb) for the entire assembled and configured wardrobe.
Adjustable Foot Range: Approx. 20 mm for leveling.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Frame is wobbly	Cam locks not tight; uneven floor	Tighten all cam locks; adjust feet to level the frame.
Doors not aligning	Hinges need adjustment	Use a screwdriver to adjust the height and depth screws on the hinges.
Shelf sagging	Overloaded; supports not correctly installed	Reduce weight; ensure shelf supports are fully inserted into side panel holes.
Difficulty attaching back panel	Frame not square	Loosen cam locks, square the frame on the floor, then retighten before attaching back panel.
Wall attachment loose	Screws not in stud; anchors failed	Relocate attachment point to a wall stud or use heavier-duty anchors suitable for the load.

Warranty and Support

IKEA limited warranty applies. Refer to the IKEA warranty document included with your purchase or available at IKEA stores.

For missing parts or assembly support: Visit the IKEA website or contact your local IKEA store.

Online Instructions: Additional assembly videos and guides can be found at www.ikea.com.

Important: Retain this manual for future reference.