IKEA OBEGRÄNSAD 405.251.24 Shelf instructions manual

The IKEA OBEGRÄNSAD 405.251.24 is a versatile wall shelf unit designed for storage and display. It features a clean, modern design with metal brackets and particleboard shelves, suitable for various rooms. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.

1. Parts & Hardware Included 2. Safety Instructions 3. Tools Required 4. Assembly Steps 5. Wall Mounting Installation 6. Weight Capacity & Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Contact IKEA if any items are missing.

Part NameQuantityDescription/Part Number
Shelf board2Particleboard, white finish
Metal bracket2Wall mounting bracket, silver
Screw8Wall anchor screws (for solid walls)
Wall plug8Plastic anchors for drywall
Allen key1Included tool for assembly
Instruction manual1This document

Safety Instructions

Read all instructions before assembly and installation.

  1. Use two people for assembly to prevent injury or damage.
  2. Ensure wall is suitable for mounting (check for studs or use appropriate anchors).
  3. Do not exceed maximum weight capacity (see Specifications).
  4. Keep small parts away from children to avoid choking hazards.
  5. Assemble on a soft surface to avoid scratching shelves.

WARNING! Improper installation can cause the shelf to fall, resulting in injury or damage. Always mount into wall studs or use suitable anchors for your wall type.

Tools Required

Tip: Using a power drill will make installation faster and easier.

Assembly Steps

Follow these steps in order. Do not fully tighten screws until all parts are aligned.

  1. Attach brackets to shelves: Place shelf board face down on a protected surface. Position metal bracket at marked locations on the underside of the shelf.
  2. Secure brackets: Using the provided Allen key, insert and tighten screws through bracket holes into pre-drilled holes in the shelf. Do not overtighten.
  3. Repeat for second shelf: Assemble the second shelf unit identically.
  4. Check alignment: Ensure brackets are parallel and securely attached.

CAUTION! Overtightening screws can damage the particleboard.

Wall Mounting Installation

This is the most critical step. A level installation is essential.

  1. Plan layout: Decide on shelf height and spacing. Use a pencil to lightly mark desired positions on the wall.
  2. Locate studs: Use a stud finder to locate wooden wall studs. Mounting into studs provides the strongest hold. If no stud is available, you must use appropriate wall anchors for your wall type (drywall, plaster, etc.).
  3. Mark bracket holes: Hold one assembled shelf unit against the wall at the desired height. Use a level to ensure it is perfectly horizontal. Mark the screw holes on the wall through the bracket holes. Repeat for the second shelf, measuring to ensure proper spacing.
  4. Drill pilot holes: Drill holes at the marked points. For studs, drill a pilot hole slightly smaller than the screw diameter. For drywall, insert the provided plastic wall plugs.
  5. Mount shelves: Align the bracket holes with the drilled holes. Insert and tighten the screws using a screwdriver or drill. Ensure the shelf is firmly attached and does not wobble. Repeat for the second shelf.
  6. Final check: Place a level on each shelf to confirm they are horizontal. Gently apply downward pressure to test stability.

WARNING! The shelf is only intended for indoor use on suitable walls. Do not mount above beds, sofas, or in areas where a fall could cause injury.

Weight Capacity & Specifications

Important: Do not place hot, wet, or excessively heavy items (like large potted plants or heavy books beyond capacity) on the shelves.

Care & Maintenance

To ensure longevity and appearance of your shelf.

  1. Cleaning: Wipe with a damp, soft cloth. Do not use abrasive cleaners, scouring pads, or chemical solvents.
  2. Drying: Immediately dry the surface with a clean cloth to prevent moisture damage.
  3. Inspection: Periodically check the tightness of screws and brackets. Re-tighten if necessary.
  4. Relocation: To move, remove all items, unscrew from wall, and patch old holes before reinstalling in a new location.

CAUTION! Particleboard is susceptible to water damage. Avoid prolonged exposure to moisture.

Troubleshooting

ProblemPossible CauseSolution
Shelf is not levelWall markings were uneven; brackets not aligned during mounting.Unscrew, re-level using a longer spirit level, and remount.
Shelf wobbles or feels looseScrews not tight; mounted into weak drywall without proper anchors.Tighten all screws. If in drywall, ensure you are using correct, heavy-duty wall anchors rated for the shelf's weight.
Brackets don't align with shelf holesShelf may be upside down; brackets reversed.Check assembly diagram. Ensure shelf is face down and brackets are oriented correctly during assembly.
Cannot screw into wallHitting a metal plate or hard material.Do not force. Choose a new mounting location a few inches away, ensuring you are not drilling into electrical wires or pipes.
Surface damage on shelfScratched during assembly.Assemble on a soft blanket or carpet. Minor scratches can be touched up with a matching furniture marker.

Warranty & Support

IKEA limited warranty applies. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for full terms and conditions.

For missing parts or assembly support: Visit the IKEA website or contact your local IKEA store with the product name (OBEGRÄNSAD) and article number (405.251.24).

Online Resources: Assembly videos and guides are often available at www.ikea.com.

Safety Notice: This furniture must be securely attached to the wall to prevent tip-over accidents, especially in households with children.

IKEA OBEGRÄNSAD 405.251.24 Shelf instructions manual © - All Rights Reserved 2025