IKEA NYFORS 503.031.13 Floor Lamp instructions manual

The IKEA NYFORS 503.031.13 is a modern floor lamp featuring a sleek design with a metal base and a fabric shade. It provides ambient lighting suitable for living rooms, bedrooms, or reading corners. The lamp includes an in-line switch on the cord for easy operation and requires assembly. Below are key sections for safety, features, assembly, installation, operation, care, and troubleshooting.

1. Features at a Glance 2. Parts Included 3. Safety Information 4. Assembly Instructions 5. Installation & Placement 6. Operation 7. Recommended Bulb 8. Care & Cleaning 9. Troubleshooting 10. Warranty & Support

Features at a Glance

Key components: Metal base, fabric shade, in-line switch, adjustable height (where applicable), and pre-assembled cord set.

Feature	Description
Design	Modern floor lamp with metal base and fabric shade
Switch	In-line switch on the cord for easy on/off control
Shade Material	Fabric diffuser for soft, ambient light
Base Material	Sturdy metal for stability
Assembly Required	Minimal assembly with included hardware
Bulb Compatibility	See "Recommended Bulb" section

Parts Included

Unpack and verify all parts before starting assembly.

Base: Metal lamp base (1 piece)
Pole/Shaft: Main support pole (1 piece)
Shade: Fabric lamp shade (1 piece)
Hardware: Screws, washers, and any connectors as needed
Cord Set: Pre-assembled power cord with in-line switch
Instruction Manual (this document)

NOTE: Contact IKEA if any parts are missing or damaged.

Safety Information

WARNING! To reduce the risk of fire, electric shock, or injury:

Read all instructions before assembly and use.
Unplug the lamp before installing or replacing the light bulb, or when cleaning.
Do not use the lamp outdoors or in damp/wet locations.
Use only the recommended bulb type and wattage (see section 7).
Do not operate the lamp if the cord or plug is damaged.
Keep the lamp away from flammable materials and heat sources.
This lamp is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, unless supervised.
Ensure the lamp is placed on a stable, level surface to prevent tipping.

Assembly Instructions

Estimated assembly time: 10-15 minutes. Tools required: None (hardware included).

Prepare Workspace: Clear a flat, soft surface to avoid scratching parts.
Attach Pole to Base: Insert the lower end of the pole into the base socket. Secure it by tightening the provided screw(s) with your fingers or the included tool.
Attach Shade: Slide the fabric shade over the top of the pole. Ensure it sits securely on the shade holder or lip. Some models may require attaching the shade with a finial (decorative nut)—screw it on clockwise until snug.
Route the Cord: Ensure the power cord runs neatly along the pole and out from the base. Do not pinch the cord.
Final Check: Ensure all connections are tight and the lamp stands upright without wobbling.

Tip: Do not over-tighten screws, as this may strip the threads.

Installation & Placement

Choose a location near a power outlet. Ensure the cord can reach the outlet without stretching.
Place the lamp on a firm, level floor surface.
Keep the lamp away from high-traffic areas where it could be knocked over.
Maintain a safe distance from curtains, bedding, or other flammable materials.
Plug the cord into a standard 120V AC household outlet.

CAUTION! Do not run the cord under carpets or rugs, as this may cause overheating.

Operation

Operating the NYFORS floor lamp is simple:

Insert Bulb: Ensure the lamp is unplugged. Screw in the recommended bulb (see below) into the socket at the top of the pole. Do not exceed the maximum wattage.
Power On: Plug the cord into the wall outlet.
Switch On/Off: Use the in-line switch on the cord to turn the lamp on or off.

Recommended Bulb: Max 1 x E26/E27 base bulb. Use an LED or CFL bulb with a maximum wattage equivalent to 13W (100W incandescent equivalent) for energy efficiency and to prevent overheating. The lamp is designed for non-dimmable bulbs unless otherwise specified.

Care & Cleaning

Always unplug the lamp before cleaning.

Shade: Use a soft brush or vacuum cleaner with a soft brush attachment to remove dust. Do not wash the fabric shade.
Base and Pole: Wipe with a soft, dry cloth. For stubborn marks, use a slightly damp cloth and dry immediately. Do not use abrasive cleaners or chemicals.
Cord: Wipe with a dry cloth. Check regularly for damage.

WARNING! Never immerse the lamp, cord, or plug in water or other liquids.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Bulb burnt out; not plugged in; switch off	Replace bulb; ensure plug is fully inserted into outlet; check that in-line switch is in the ON position.
Lamp flickers	Loose bulb; faulty bulb; poor connection	Turn off and unplug. Tighten bulb securely. If problem persists, try a new bulb.
Lamp is unstable/wobbly	Assembly not tight; uneven floor	Check and tighten all connections between base, pole, and shade. Place on a level surface.
Overheating	Bulb wattage too high; poor ventilation	Use only the recommended bulb wattage. Ensure lamp is not covered or placed against fabrics.
Damaged cord or plug	Physical damage	Stop using immediately. Do not attempt to repair. Contact IKEA for support.

Warranty & Support

This IKEA product is covered by the IKEA limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for specific terms and duration.

For assistance:

Visit the IKEA website: www.ikea.com
Contact IKEA customer support at 1-888-888-4532
Visit your local IKEA store with your proof of purchase.

Recycling: At the end of its life, do not dispose of this product with household waste. Recycle according to local regulations for electrical products.