IKEA NYFORS 004.162.83 Floor Lamp instructions manual

The IKEA NYFORS 004.162.83 is a modern floor lamp featuring a minimalist design with a metal frame, adjustable shade, and integrated on/off switch. It requires assembly and uses a standard E27 bulb (max 13W LED or equivalent, not included). Below are key sections for safety, parts list, assembly instructions, operation, care, and troubleshooting.

1. Parts Included 2. Safety Instructions 3. Assembly Instructions 4. Specifications 5. Operation & Controls 6. Bulb Replacement 7. Care & Cleaning 8. Warranty Information 9. Troubleshooting

Parts Included

Before assembly, check that you have all parts listed below.

Part Number	Description	Quantity
A	Base plate with foot	1
B	Main vertical pole	1
C	Adjustable arm	1
D	Lamp shade	1
E	Socket with integrated switch	1
F	Mounting screws and washers	1 set
G	Hex key (Allen wrench)	1

Note: Light bulb (E27, max 13W LED) is not included.

Safety Instructions

Read all instructions before assembly and use.

Electrical Safety: Unplug lamp before assembly, cleaning, or bulb replacement.
Bulb Wattage: Use only E27 base bulbs with maximum 13W LED or equivalent. Higher wattage may cause overheating and fire hazard.
Placement: Place on a stable, level surface away from heat sources, water, and high-traffic areas.
Cord Management: Do not pinch or damage the power cord. Keep away from sharp edges and hot surfaces.
Children: Keep out of reach of young children during assembly and operation.

WARNING! Risk of electric shock. Do not disassemble the socket or electrical components.

Assembly Instructions

Estimated assembly time: 15-20 minutes. Tools required: Hex key (provided).

Attach Base: Place base plate (A) on a soft surface. Insert the main pole (B) into the base and secure with the provided screw using the hex key.
Connect Arm: Attach the adjustable arm (C) to the top of the main pole. Align holes and tighten the screw firmly.
Install Socket: Thread the socket unit (E) through the arm and shade opening. Secure it to the arm with the locking nut.
Attach Shade: Position the lamp shade (D) over the socket. Align the shade's mounting holes with the arms of the socket bracket and secure with small screws.
Final Check: Ensure all screws are tight and components are stable. Do not plug in yet.

Tip: Assemble on a carpet or soft mat to avoid scratching the parts.

Specifications

Model: NYFORS 004.162.83
Type: Floor Lamp, Adjustable
Material: Metal frame, fabric/plastic shade
Color: Black/White (as per variant)
Height: Adjustable from 140cm to 160cm
Base: Stable round foot, diameter 30cm
Bulb: 1 x E27 socket (max 13W LED or equivalent)
Switch: Integrated on/off switch on socket
Cord Length: 180cm
Voltage: 100-240V AC, 50/60Hz
Weight: 3.5 kg (assembled)

Operation & Controls

Once assembled and bulb installed:

Plug the power cord into a standard wall outlet.
Use the integrated switch on the socket to turn the lamp ON/OFF.
Adjust the lamp arm to direct light as needed. The arm pivots at two joints.
Adjust the shade angle by gently tilting it (if model allows).

Note: The lamp does not have a dimmer. Use dimmable bulbs if dimming function is required.

Bulb Replacement

Unplug the lamp from the wall outlet and allow bulb to cool if recently used.
Gently press the lamp shade upward or sideways (depending on model) to access the bulb.
Unscrew the old bulb counterclockwise and remove it.
Screw in the new E27 bulb clockwise until snug. Do not overtighten.
Replace the shade to its original position.
Plug in the lamp and test with the switch.

CAUTION! Use only recommended bulb type and wattage to prevent damage.

Care & Cleaning

Unplug lamp before cleaning.

Shade: Wipe with a dry, soft cloth. For fabric shades, use a vacuum with brush attachment.
Frame: Wipe with a slightly damp cloth. Do not use abrasive or chemical cleaners.
Cord: Wipe with dry cloth. Check regularly for damage.

WARNING! Never immerse any part of the lamp in water or other liquids.

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included with purchase or available at www.ikea.com. Warranty covers material and manufacturing defects under normal household use. Keep your receipt as proof of purchase.

For service or claims, contact IKEA customer support at 1-888-888-4532 or visit your local IKEA store.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Not plugged in / Bulb burnt out / Switch off	Plug in lamp; replace bulb; ensure switch is ON.
Lamp flickers	Loose bulb / Faulty bulb / Poor connection	Turn off, unplug, and tighten bulb. Try a different bulb.
Lamp is unstable	Base not fully assembled / Uneven floor	Tighten base screw. Place on a level surface.
Arm does not hold position	Joint screws loose	Tighten the pivot joint screws with the hex key.
Overheating	Bulb wattage too high / Ventilation blocked	Use only recommended max 13W LED bulb. Ensure shade vents are clear.

For further assistance: Contact IKEA customer support or visit www.ikea.com.