IKEA NORDMELA 104.216.65 4 Drawer Dresser Instructions Manual

The IKEA NORDMELA 104.216.65 is a 4-drawer dresser designed for bedroom storage, featuring a clean Scandinavian design, smooth-gliding drawers, and durable construction. Below are key sections for safety, parts list, assembly instructions, usage, care, and troubleshooting.

1. Parts & Hardware 2. Safety Instructions 3. Assembly Steps 4. Product Specifications 5. Drawer Installation & Adjustment 6. Care & Maintenance 7. Wall Attachment 8. Troubleshooting 9. Warranty & Support

Parts & Hardware

All components included in the package. Verify against this list before assembly.

Part Name	Quantity	Description
Dresser Frame	1	Main body structure
Drawer Fronts	4	Front panels for drawers
Drawer Sides	8	Left and right side panels for each drawer
Drawer Bottoms	4	Particleboard bases for drawers
Back Panel	1	Fiberboard back of dresser
Drawer Runners	8	Metal glide mechanisms
Cam Locks	12	Plastic connectors for frame
Screws	Various	Assembly screws included
Wall Attachment Kit	1	Brackets and screws for securing to wall
Allen Key	1	Tool for assembly

Safety Instructions

Read all instructions before assembly. Ensure a safe environment.

Assemble on a soft surface to avoid scratching parts.
Use two people for lifting and positioning the dresser.
Keep small hardware away from children to prevent choking.
Always secure the dresser to the wall using the provided kit to prevent tipping.

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this dresser to the wall.

Assembly Steps

Follow these steps in order. Estimated assembly time: 45-60 minutes.

Prepare Workspace: Clear an area large enough to lay out all parts.
Assemble Frame: Connect side panels to top and bottom panels using cam locks. Tighten with provided tool.
Attach Back Panel: Place the back panel into the grooves on the frame. Secure with nails or screws provided.
Install Drawer Runners: Attach the metal runners to the inside of the dresser frame at marked positions.
Assemble Drawers: Connect drawer sides to front and back using cam locks. Insert drawer bottom into slots.
Attach Drawer Fronts: Slide drawer into frame, then attach the drawer front to the drawer box using screws from inside.
Final Check: Ensure all screws and cam locks are tight. Test each drawer for smooth operation.

CAUTION! Do not overtighten screws, as this may strip the particleboard.

Product Specifications

Product Name: NORDMELA
Article Number: 104.216.65
Dimensions (W x H x D): 31 ½" x 37 ¾" x 18 ⅛" (80 cm x 96 cm x 46 cm)
Weight: 55 lbs (25 kg)
Material: Particleboard, Fiberboard, Plastic, Steel
Finish: White, Ash Veneer
Drawer Capacity: Each drawer holds up to 22 lbs (10 kg)
Recommended Use: Bedroom storage for clothing and personal items.

Drawer Installation & Adjustment

For smooth drawer operation, ensure runners are aligned correctly.

Installation: Insert the drawer into the runners at a slight upward angle until you hear a click. Pull out to test.

Adjustment: If a drawer is uneven or sticks, loosen the screws on the runner slightly, adjust the position, and retighten.

Removal: To remove a drawer, pull it out fully, press the plastic tabs on both sides of the runner, and lift the drawer out.

Care & Maintenance

Clean with a damp cloth and mild detergent. Wipe dry immediately.

Avoid abrasive cleaners, scouring pads, or solvents.
Do not place hot or wet items directly on the surface.
Distribute weight evenly in drawers to prevent sagging.

CAUTION! Excessive moisture can cause particleboard to swell. Never soak the furniture.

Wall Attachment

CRITICAL: To prevent tip-over, you MUST secure the dresser to the wall.

Locate wall studs using a stud finder.
Position the dresser against the wall in its final location.
Attach the provided anti-tip bracket to the wall stud with screws.
Attach the other part of the bracket to the back, top inside of the dresser frame.
Tighten all screws securely.

Tip: If you cannot find a stud, use appropriate wall anchors for your wall type.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Drawer sticks or is hard to open	Misaligned runners or overloaded drawer	Adjust runner alignment; reduce weight in drawer.
Dresser wobbles	Uneven floor or loose connections	Check floor; tighten all cam locks and screws.
Cam lock won't tighten	Cam lock not engaged properly	Disassemble step, ensure dowel is fully inserted into cam, then turn.
Gap between drawer fronts	Drawer fronts not aligned during installation	Loosen screws holding drawer front, adjust position, retighten.
Scratches on surface	Assembly on hard surface	Use felt pads under items; minor scratches can be touched up with matching paint.

Note: For missing parts or damaged components, contact IKEA customer service.

Warranty & Support

IKEA Limited Warranty applies. See IKEA terms and conditions for details.

For assembly help, missing parts, or product support:

Visit: www.ikea.com
Contact IKEA Customer Service: 1-888-888-4532
Reference Article Number: 104.216.65

Recycling: At end of life, disassemble and recycle materials according to local regulations.