IKEA NISSEDAL 205.037.74 Mirror instructions manual

The IKEA NISSEDAL 205.037.74 is a wall-mounted mirror designed for bathrooms and other rooms. It features a sturdy frame, safety backing, and mounting hardware for secure installation. Below are key sections for safety, parts included, step-by-step assembly, mounting instructions, care, and warranty information.

1. Parts Included 2. Tools Needed 3. Safety Instructions 4. Assembly Steps 5. Wall Mounting 6. Care & Maintenance 7. Specifications 8. Troubleshooting 9. Warranty & Support

Parts Included

Check that all parts are present before starting assembly.

Part Number	Description	Quantity
100001	Mirror panel	1
100002	Frame top section	1
100003	Frame bottom section	1
100004	Side frame left	1
100005	Side frame right	1
200101	Wall bracket	2
300201	Screw pack (screws & wall plugs)	1 set
400301	Allen key	1

Tools Needed

Tools not included that you will need for assembly and mounting.

Phillips screwdriver
Drill with appropriate drill bit (for wall type)
Level
Pencil
Measuring tape
Hammer (if using wall plugs)

Safety Instructions

WARNING! Failure to follow these instructions can result in serious injury or damage.

This mirror is heavy. Use two people for handling and assembly.
Ensure the wall can support the mirror's weight. Use appropriate wall anchors for your wall type (drywall, plaster, concrete).
Keep all small parts away from children to avoid choking hazards.
Do not hang the mirror above a bathtub or in an area where it could fall into water.
Wear safety glasses when drilling into walls.
Check that the mirror is securely mounted before use.

Assembly Steps

Assemble the mirror frame on a soft, flat surface to avoid scratches.

Step 1: Lay the mirror panel face down on a soft cloth or cardboard.
Step 2: Attach the side frames (100004 & 100005) to the bottom frame section (100003) using the provided screws and Allen key. Do not fully tighten yet.
Step 3: Place the assembled bottom and sides around the mirror panel.
Step 4: Attach the top frame section (100002) to the side frames. Ensure all corners are aligned.
Step 5: Tighten all screws securely with the Allen key, but do not overtighten.
Step 6: Carefully turn the assembled mirror over and check for stability.

CAUTION! Handle the mirror glass with care. Avoid putting pressure on the center of the panel.

Wall Mounting

Mounting the mirror securely is critical for safety.

Locate Studs: Use a stud finder to locate wall studs. Mounting into studs is ideal. If not possible, use heavy-duty wall anchors suitable for your wall type and the mirror's weight.
Mark Positions: Hold the mirror against the wall at the desired height. Use a pencil to mark the top corners. Use a level to ensure marks are even.
Attach Brackets: Attach the wall brackets (200101) to the back of the mirror frame using the provided screws.
Drill Holes: At your marked positions, drill pilot holes into the wall. Insert wall plugs if needed.
Mount Mirror: With help from another person, lift the mirror and hook the brackets onto the screws in the wall. Ensure it is level and secure.
Final Check: Gently pull on the mirror to confirm it is firmly attached to the wall.

Tip: The ideal mounting height is with the center of the mirror at eye level for the primary user.

Care & Maintenance

Proper care will keep your mirror looking new.

Clean the mirror with a soft, lint-free cloth.
Use a mild glass cleaner or a solution of vinegar and water. Spray the cleaner onto the cloth, not directly onto the mirror, to avoid liquid seeping behind the frame.
Wipe the frame with a dry or slightly damp cloth. Do not use abrasive cleaners or scouring pads.
Avoid exposing the mirror to excessive moisture or steam for prolonged periods to protect the backing.

CAUTION! Never use harsh chemicals, ammonia-based cleaners, or sharp objects on the mirror surface.

Specifications

Article Number: 205.037.74
Model Name: NISSEDAL
Dimensions: Width: 80 cm (31 ½ ") | Height: 120 cm (47 ¼ ") | Depth: 4 cm (1 ½ ")
Weight: Approximately 12 kg (26.5 lbs)
Frame Material: Steel, Epoxy/polyester powder coating
Mirror Type: Clear float glass with safety backing
Intended Use: Indoor use only. Suitable for bathroom (not above bathtub), bedroom, hallway.
Max Load: Supports its own weight only. Do not hang items on the frame.

Troubleshooting

Problem	Possible Cause	Solution
Frame feels loose	Screws not tightened	Check and tighten all frame connection screws with the Allen key.
Mirror wobbles on wall	Wall anchors not secure / not in stud	Remount using proper heavy-duty anchors or locate and mount into wall studs.
Difficulty aligning frame	Parts assembled in wrong order	Disassemble and follow Step-by-Step Assembly (Section 5) carefully.
Streaks on mirror after cleaning	Cleaner sprayed directly on glass	Spray cleaner on cloth first, then wipe mirror. Use a dry cloth for final polish.
Missing part	Part not in box or lost	Contact IKEA customer service with your article number (205.037.74) for replacement parts.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the packaging or available at IKEA stores.

For Assembly Support: Visit the IKEA website and search for the product name "NISSEDAL" to find digital assembly instructions and videos.

For Missing Parts or Product Issues: Contact IKEA customer service in your country or visit your local IKEA store with your receipt and article number (205.037.74).

Safety Notice: IKEA disclaims any liability for improper installation or use not in accordance with this manual.