IKEA NEIDEN 003.952.52 Bed Frame instructions manual

The IKEA NEIDEN 003.952.52 is a sturdy and functional bed frame designed for easy assembly and everyday use. It features a slatted bed base for mattress support, a solid pine construction, and a clean Scandinavian design. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Hardware 2. Safety Information 3. Assembly Instructions 4. Care & Maintenance 5. Specifications 6. Troubleshooting 7. Warranty & Support

Parts & Hardware

Before assembly, verify all parts are present. Check packaging materials thoroughly.

Part Number	Description	Quantity
100001	Side Rail (Long)	2
100002	Headboard/Footboard Panel	2
100003	Center Support Beam	1
100004	Slatted Bed Base	1 set
100005	Wooden Dowel	12
100006	Cam Lock Nut	6
100007	Screw (50mm)	16
100008	Allen Key	1

Safety Information

Read all instructions before assembly. Ensure a clean, spacious work area.

Weight Capacity: Max load 220 lbs (100 kg) per side rail.
Stability: Assemble on a flat, level surface. Check all connections are tight.
Tools: Use only the provided Allen key. Do not overtighten screws.
Children: Keep small parts away from children during assembly.

WARNING! Bed frame is heavy; use two people for lifting and assembly to avoid injury.

Assembly Instructions

Follow steps in order. Allow approximately 45-60 minutes for assembly.

Step 1: Lay side rails (100001) parallel on floor. Insert wooden dowels (100005) into pre-drilled holes on inner sides.
Step 2: Attach headboard and footboard panels (100002) to side rails using dowels. Secure with cam lock nuts (100006) and tighten with Allen key.
Step 3: Install center support beam (100003) across middle of frame. Attach with screws (100007) provided.
Step 4: Place slatted bed base (100004) onto frame rails. Ensure slats are evenly spaced and click into place on support brackets.
Step 5: Double-check all connections are secure. Gently shake frame to test stability.
Step 6: Place mattress on slatted base. Do not use box spring.

Tip: For easier assembly, keep all parts labeled and organized.

Care & Maintenance

Proper care extends the life of your bed frame.

Cleaning: Wipe with a dry or slightly damp cloth. Do not use abrasive cleaners.
Tightening: Check screw and cam lock tightness every 3-6 months.
Slats: Ensure slats remain properly seated on support brackets. Rearrange if sagging occurs.
Environment: Avoid excessive humidity or direct sunlight to prevent wood warping.

CAUTION! Do not use wax, polish, or chemical cleaners on the pine surface.

Specifications

Model: NEIDEN 003.952.52
Frame Material: Solid pine, Clear acrylic lacquer
Mattress Size Compatibility: Twin (38" x 75" / 96.5 x 190.5 cm)
Overall Dimensions (Assembled): 41.75" W x 79.5" L x 8.25" H (106 x 202 x 21 cm)
Under-bed Clearance: 5.5 inches (14 cm)
Weight Capacity (Total): 440 lbs (200 kg)
Slatted Bed Base Type: Luroy, curved slats for mattress support
Country of Origin: Designed and quality tested by IKEA of Sweden

Troubleshooting

Issue	Possible Cause	Solution
Frame wobbles or squeaks	Loose connections	Tighten all cam locks and screws with Allen key. Ensure frame is on level floor.
Slats falling out	Slats not properly clicked into brackets	Remove mattress and reposition each slat until it clicks securely into the support brackets.
Difficult assembly	Parts misaligned	Disassemble step and re-insert dowels carefully before tightening cam locks.
Missing part	Packaging error	Contact IKEA customer service with model number and part list for replacement.
Mattress sagging in middle	Center support beam not installed or loose	Verify center beam is correctly attached and screws are tight.

Warranty & Support

IKEA Limited Warranty: 1-year warranty from date of purchase against manufacturing defects. Proof of purchase required.

For Support:
Visit: www.ikea.com
Customer Service: 1-888-888-4532
For spare parts, use the part numbers listed in this manual.

Recycling: Dispose of packaging responsibly. Check local recycling guidelines for cardboard and plastic.