IKEA NANNARP 092.098.49 Leg instructions manual

The IKEA NANNARP 092.098.49 Leg is a furniture leg designed for use with compatible IKEA tabletops, countertops, and other surfaces. It provides stable support and an adjustable height feature for leveling on uneven floors. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Furniture 7. Height Adjustment 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Adjustable leg with threaded insert, mounting plate, protective foot cap, and height adjustment mechanism.

Feature	Description
Adjustable Height	Threaded mechanism for fine-tuning leg length
Mounting Plate	Pre-drilled holes for secure attachment to furniture
Protective Foot Cap	Non-slip, floor-protecting cap
Threaded Insert	For secure connection to leg receiver
Material	Steel construction with powder-coated finish
Weight Capacity	Designed to support specified load limits
Compatibility	Designed for use with IKEA NANNARP series and other compatible tops
Tool-Free Adjustment	Some models allow hand-tightening of adjustment mechanism
Leveling Feature	Allows compensation for uneven floors
Installation Hardware	Included screws and mounting accessories

Installation

Unpack and inspect contents. Ensure you have all parts before beginning.

Position furniture top upside down on a soft, protected surface.
Align leg mounting plate with pre-drilled holes in furniture underside.
Insert provided screws through mounting plate into furniture.
Tighten screws securely using appropriate screwdriver or Allen key.
Attach protective foot cap to bottom of leg if not pre-installed.

WARNING! Ensure furniture is stable during installation. Use appropriate tools to avoid stripping screws.

First-Time Setup

After installation, prepare legs for use.

Turn furniture right-side up with assistance.
Adjust height: Rotate leg clockwise to shorten, counterclockwise to lengthen.
Check level: Use spirit level on furniture surface.
Fine-tune each leg until furniture is stable and level.
Test stability by applying gentle pressure to different corners.

CAUTION! Always lift furniture with help; do not drag across floors to prevent damage.

Specifications

Product Code: 092.098.49
Type: Adjustable Furniture Leg
Material: Steel with powder coat finish
Height Range: Adjustable within specified range (e.g., 27-30 inches)
Mounting: Plate mounting with 4-hole pattern
Load Capacity: Up to [specified weight] per leg
Color: Black/White/Chrome as specified
Included Hardware: Mounting screws, possibly washers
Compatibility: IKEA NANNARP tabletops, desks, counters
Warranty: IKEA limited warranty applies

Controls and Settings

Height adjustment is primary control mechanism.

Adjustment Method: Rotate leg body to extend/retract. Some models may include locking nut or set screw to secure desired height.

Leveling: Adjust each leg independently to compensate for floor irregularities. Use spirit level on surface for accuracy.

Mounting: Ensure screws are tight but not overtightened to avoid damaging furniture material.

Connecting to Furniture

Compatible with IKEA NANNARP series and other tops with appropriate mounting points.

Verify furniture has compatible mounting points (pre-drilled holes or reinforcement plates).
Match leg mounting plate hole pattern to furniture holes.
Use only provided or recommended hardware.
Ensure all legs are installed symmetrically for balanced support.

Tip: For heavier furniture, install center support legs if recommended.

Height Adjustment

Allows customization and leveling on uneven surfaces.

Identify needed adjustment: Check which corners are uneven.
Rotate leg: Turn clockwise to lower, counterclockwise to raise.
Small increments: Make gradual adjustments and re-check level.
Lock position: If model includes locking mechanism, secure after adjustment.
Test stability: Ensure furniture doesn't wobble after adjustment.
Re-adjust as needed: Seasonal changes may require re-leveling.

WARNING! Do not exceed maximum extension height. Ensure locking mechanisms are engaged before use.

Safety Features

Stability: Wide base design prevents tipping. Load Capacity: Rated for specified weight limits. Non-slip Feet: Prevent sliding on smooth floors. Secure Mounting: Designed to remain attached when properly installed.

Care & Cleaning

Wipe with damp cloth; dry immediately. Avoid abrasive cleaners.

CAUTION! Do not use harsh chemicals; avoid excessive moisture on adjustment mechanisms.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Furniture wobbles	Uneven floor/legs not adjusted	Adjust leg heights individually; use level to check surface.
Leg won't adjust	Threads dirty or damaged	Clean threads; ensure no cross-threading; apply light lubricant if needed.
Leg feels loose	Mounting screws not tight	Tighten all mounting screws; check for stripped threads.
Foot cap falls off	Not properly seated	Press firmly until clicks; replace if damaged.
Surface not level	Legs at different heights	Adjust each leg incrementally; re-check with level.

Replacement: Contact IKEA for missing or damaged parts.

Service: www.ikea.com or local IKEA customer service.