IKEA MISTERHULT 404.410.25 Lighting instructions manual

The IKEA MISTERHULT 404.410.25 is a modern LED lighting fixture designed for indoor use, featuring energy-efficient LED technology, adjustable brightness levels, multiple color temperature settings (warm white to cool daylight), remote control operation, timer function, and memory function for preferred settings. Compatible with standard E27 bulbs (not included), includes mounting hardware for ceiling installation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: LED light panel, Remote Control, Mounting bracket, Power cable, Instruction manual.

Installation

Unpack and inspect all components. Ensure power is turned off at circuit breaker.

1. Mount bracket: Secure mounting bracket to ceiling using provided screws and anchors.
2. Connect wires: Match wire colors (brown/live to live, blue/neutral to neutral, green/yellow to ground).
3. Attach light fixture: Align fixture with bracket and twist to lock in place.
4. Install bulb: Screw compatible E27 LED bulb into socket (not included).
5. Restore power and test.

WARNING! Installation should be performed by qualified electrician. Ensure power is disconnected before installation.

First-Time Setup

After installation, configure initial settings.

1. Power on: Turn on at wall switch or circuit breaker.
2. Pair remote: Point remote at light and press POWER button for 3 seconds until light blinks.
3. Set default brightness: Use remote to adjust to preferred level (default 100%).
4. Select color temperature: Cycle through options to find preferred setting.
5. Test all functions: Verify remote control operation for all features.

CAUTION! Do not look directly at LED light source at close range. Use appropriate eye protection if necessary.

Specifications

• Model: MISTERHULT 404.410.25
• Power Consumption: Max 15W (with compatible LED bulb)
• Luminous Flux: Up to 1500 lumens (depends on bulb used)
• Color Temperature: 3000K / 4000K / 6500K (selectable)
• CRI (Color Rendering Index): >80 (with recommended bulb)
• Dimming Range: 10%-100% smooth dimming
• Operating Voltage: AC 100-240V, 50/60Hz
• Socket Type: E27 standard
• Remote Control Range: Up to 8 meters (26 feet)
• Operating Temperature: -20°C to 40°C (-4°F to 104°F)
• Warranty: 2 years limited warranty

Controls and Settings

Primary control via remote control. Wall switch can be used for basic on/off.

Remote Functions: POWER ON/OFF, BRIGHTNESS +/-, COLOR TEMP (cycles through 3 settings), TIMER SET (1-8 hours), MEMORY (saves current settings).

Light Indicator: Blue LED indicates power on; blinking during pairing mode.

Settings Memory: Automatically saves last used brightness and color temperature when powered off via remote.

Connecting to Power

Must be connected to appropriate electrical circuit.

1. Turn off power at circuit breaker before any electrical work.
2. Connect wires according to local electrical codes (brown/live, blue/neutral, green/yellow ground).
3. Use wire connectors (not included) to secure connections.
4. Ensure no bare wires are exposed.
5. Test connection with circuit tester before restoring power.

Tip: For best performance, use on a dedicated lighting circuit or with other low-power devices.

Using the Remote Control

Remote requires 2x AAA batteries (not included).

1. Insert batteries: Match polarity markings in battery compartment.
2. Pairing: Point remote at light, press and hold POWER for 3 seconds until light blinks.
3. Basic operation: POWER turns light on/off; +/- adjusts brightness.
4. Color temperature: Press COLOR button to cycle through warm/neutral/cool.
5. Timer: Press TIMER, then use +/- to set hours (1-8), press TIMER again to confirm.
6. Memory: Current settings are automatically saved when turned off via remote.

WARNING! Keep remote away from children. Dispose of batteries properly.

Smart Features

Timer Function: Set automatic shut-off from 1 to 8 hours. Useful for bedtime or energy saving.

Memory Function: Remembers brightness and color temperature settings when powered off via remote (not when powered off at wall switch).

Energy Saving: LED technology uses up to 85% less energy than traditional incandescent bulbs.

Care & Cleaning

Turn off and disconnect from power before cleaning.

1. Use dry, soft cloth to wipe light surface.
2. For stubborn dirt, use slightly damp cloth (water only).
3. Do not use chemical cleaners, abrasives, or solvents.
4. Clean remote with dry cloth only.
5. Replace LED bulb when brightness decreases significantly (typically after 25,000 hours).

CAUTION! Never immerse light fixture in water. Do not clean while light is hot.

Regulatory Information

CE Certified: Complies with European safety standards. RoHS Compliant: Free of hazardous substances. Energy Class: A+ (with recommended LED bulb). This product meets all applicable EU directives. For recycling information, contact local authorities. IKEA and MISTERHULT are trademarks of Inter IKEA Systems B.V. For support, visit www.ikea.com or contact local IKEA customer service.

Troubleshooting

Reset: Turn off at wall switch for 30 seconds, then turn back on to reset to factory defaults.

Service: Contact IKEA customer service or visit www.ikea.com for warranty claims.