IKEA MAXIMERA 490.343.29 Low Drawer instructions manual

The IKEA MAXIMERA 490.343.29 is a low-profile drawer designed for use with compatible IKEA kitchen cabinet frames. It features smooth, full-extension glides, a soft-close mechanism, and is part of the MAXIMERA drawer system for optimized storage. Below are key sections for safety, assembly, installation, use, care, and troubleshooting.

Product Overview & Contents

Key components: Drawer front panel, drawer box, MAXIMERA runner set (left and right), screws, assembly fittings, and soft-close dampers.

Safety Information

Read all instructions before assembly and installation.

1. Ensure cabinet is securely mounted to wall before installing drawer.
2. Use appropriate personal protective equipment if drilling.
3. Keep small parts away from children to avoid choking hazard.
4. Do not exceed maximum load capacity.

WARNING! Improper installation can cause drawer to detach, resulting in injury or damage. Verify all screws are tight and runners are securely engaged.

Tools Required

Gather tools before starting:

• Phillips screwdriver (size #2)
• Drill (optional, for pilot holes)
• Measuring tape
• Level
• Pencil

Note: Some packs may include an Allen key for specific fittings.

Assembly Instructions

If drawer box is not pre-assembled:

1. Lay drawer front panel face down on soft surface.
2. Attach drawer box sides to front panel using provided screws.
3. Insert drawer bottom into grooves, ensuring it sits flush.
4. Secure back panel to complete box rectangle.
5. Attach runners to sides of drawer box as indicated by pre-drilled holes.

Tip: Do not overtighten screws into particleboard to avoid stripping.

Installation into Cabinet

1. Measure and mark desired drawer height inside cabinet.
2. Attach cabinet part of runner to cabinet side walls using screws. Ensure left/right are level and at same height.
3. Engage drawer-mounted runners into cabinet runners by tilting drawer in and lowering into place until click is heard.
4. Test slide motion. Drawer should extend fully and self-close softly.

CAUTION! Ensure runners are properly aligned before loading drawer.

Adjustment & Alignment

If drawer is uneven or sticks:

• Height adjustment: Loosen screws on cabinet runner, adjust up/down, retighten.
• Side-to-side alignment: Use adjustment screws at back of runner to shift drawer left/right.
• Front alignment: Loosen screws attaching drawer front, reposition, retighten.

Check for smooth operation after each adjustment.

Use & Features

Features of MAXIMERA low drawer:

• Full extension: Drawer pulls out completely for access to contents at the back.
• Soft-close: Dampers ensure quiet, gentle closing.
• High load capacity: Designed to hold kitchen utensils, cutlery, or other items (check spec for max weight).
• Compatible fronts: Can be fitted with various IKEA drawer fronts (sold separately).

To remove drawer: Pull fully out, depress release tabs on both sides of runners, and lift drawer out.

Care & Maintenance

Clean drawer interior with damp cloth and mild detergent. Avoid abrasive cleaners.

Periodically check runner screws for tightness. Lubrication is generally not required for MAXIMERA runners.

CAUTION! Do not use silicone spray or oil on runners, as it may attract dust and impair function.

Technical Specifications

• Product name: MAXIMERA low drawer
• Article number: 490.343.29
• Dimensions (W x H x D): Refer to packaging or IKEA website for specific size.
• Material: Particleboard, foil, plastic fittings
• Runner type: Full-extension, soft-close
• Max load: [Check product label] typically 15-25 kg
• Compatibility: For use with IKEA SEKTION/METOD cabinet frames of corresponding width.

Warranty & Support

IKEA limited warranty applies. See IKEA warranty terms for details.

For missing parts or assembly support, contact IKEA customer service or visit the IKEA store where purchased.

Online assembly guides available at www.ikea.com.

Troubleshooting

Note: For persistent issues, consult IKEA assembly guide online or contact customer support.