IKEA MAXIMERA 090.407.75 High Drawer instructions manual
The IKEA MAXIMERA 090.407.75 is a high drawer designed for use with compatible IKEA kitchen and bathroom cabinet frames. It features a soft-closing mechanism, full extension runners, and a durable, easy-to-clean interior. Below are key sections for safety, parts list, assembly, installation, adjustment, care, and troubleshooting.
Parts List & Tools Required
Ensure all parts are present before beginning assembly.
| Part Description | Quantity | Image Ref. |
|---|
| Drawer front panel | 1 | A |
| Drawer box (sides, back, bottom) | 1 set | B |
| MAXIMERA runner set (left & right) | 1 pair | C |
| Soft-closing mechanism | 1 set | D |
| Assembly screws & dowels | 1 packet | E |
| Adjustment screws (for front) | 4 | F |
Tools Needed: Phillips screwdriver, hammer, measuring tape, pencil.
Safety Information
Read all instructions before assembly and installation.
- Work Area: Use a clean, flat, stable surface for assembly.
- Lifting: The drawer is heavy; use proper lifting techniques or ask for assistance.
- Secure Installation: Ensure the cabinet frame is securely fixed to the wall before installing the drawer.
- Child Safety: Do not allow children to play with or climb on the installed drawer.
WARNING! Failure to secure the cabinet frame to the wall can result in tipping, causing serious injury or death.
Assembly Instructions
Follow these steps to assemble the drawer box.
- Step 1: Lay the drawer bottom (pre-assembled panel) flat.
- Step 2: Attach the left and right side panels to the bottom using the provided dowels and screws. Ensure the pre-drilled holes align.
- Step 3: Attach the back panel to the sides and bottom, completing the box structure.
- Step 4: Check that all joints are square and tight.
Tip: Do not overtighten screws, as this may damage the particleboard.
Installation into Cabinet Frame
Installing the drawer into the SEKTION or other compatible IKEA frame.
- Mount Runners: Attach the left and right runners to the inside of the cabinet frame using the screws provided. Use a level to ensure they are perfectly horizontal and at the same height.
- Attach Drawer to Runners: Extend the runner mechanism fully. Align the drawer box with the runners and push firmly until you hear a click, indicating it is locked in place.
- Attach Front Panel: Place the drawer front panel against the cabinet frame. From inside the drawer, use the adjustment screws to attach the front panel to the drawer box. Adjust for even gaps on all sides.
CAUTION! Ensure the drawer is empty during installation to reduce weight and risk of injury.
Adjustments & Leveling
Fine-tune the drawer for smooth operation and perfect alignment.
- Height Adjustment: Loosen the screws on the rear of the runner where it attaches to the cabinet. Slide the runner up or down, then retighten.
- Front Alignment: With the drawer open, use the adjustment screws inside the drawer to move the front panel left, right, up, or down.
- Soft-Close Tension: The mechanism is pre-set. If the drawer does not close softly, check for obstructions. Do not attempt to disassemble the damper.
Care & Maintenance
Proper care will ensure long-lasting performance.
- Cleaning: Wipe the interior and exterior with a damp cloth and mild detergent. Dry immediately.
- Runners: Periodically check runners for debris. Wipe with a dry cloth. Do not lubricate.
- Weight Limit: Do not exceed the maximum load capacity of 55 lbs (25 kg).
CAUTION! Do not use abrasive cleaners, scouring pads, or strong chemicals, as they can damage the surface.
Troubleshooting
| Symptom | Possible Cause | Corrective Action |
|---|
| Drawer does not close smoothly | Obstruction; misaligned runner | Remove items blocking the path. Check runner alignment and height. |
| Front panel is crooked | Adjustment screws loose or uneven | Open drawer and re-tighten/adjust the four front mounting screws evenly. |
| Drawer sticks or is difficult to open | Dirt on runners; overloaded | Clean runners. Remove some contents to reduce weight. |
| Soft-close function not working | Damper mechanism faulty; obstruction | Ensure nothing is jamming the drawer. If faulty, contact IKEA support for a replacement damper. |
| Gaps around front panel uneven | Cabinet frame not level; panel misaligned | Ensure cabinet is level. Readjust the front panel using the adjustment screws. |
Technical Specifications
- Product Name: MAXIMERA High Drawer
- Article Number: 090.407.75
- Color: White
- Material: Particleboard, ABS plastic, steel
- Dimensions (W x H x D): Consult IKEA product page for specific size.
- Runner Type: Full-extension, soft-closing
- Max. Load Capacity: 55 lbs (25 kg)
- Compatible Frames: SEKTION, AKURUM, and other IKEA cabinet frames with correct interior width.
Warranty & Support
This IKEA product is covered by the IKEA limited warranty. For warranty terms, visit www.ikea.com.
Need Help? Visit the IKEA website for assembly guides and videos. For missing parts or further assistance, contact your local IKEA store or call IKEA customer service at 1-800-434-4532.
Recycling: At the end of its life, disassemble and recycle materials according to local regulations.
IKEA MAXIMERA 090.407.75 High Drawer instructions manual © - All Rights Reserved 2025