IKEA MÖRBYLÅNGA 092.598.44 Table instructions manual

The IKEA MÖRBYLÅNGA 092.598.44 is a versatile dining table featuring a solid wood top, sturdy construction, and a design suitable for various room settings. This manual provides essential information for safe assembly, proper use, care, and maintenance of your table. Below are key sections covering safety, parts identification, step-by-step assembly, usage guidelines, and troubleshooting.

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Table top, Legs (4), Support frame, Hardware pack.

Tools Required

Tools not included that you will need:

1. Phillips screwdriver (medium size).
2. Soft mallet (for tapping dowels).
3. Clean cloth (to protect surfaces during assembly).

NOTE: Do not use power tools at high torque to avoid damaging wood.

Safety Instructions

Read all instructions before assembly.

1. Assemble on a soft, clean surface (e.g., carpet, blanket) to prevent scratches.
2. Keep small children and pets away during assembly to avoid injury or part loss.
3. Lift with care; table top is heavy—use two people.
4. Ensure all screws and cam locks are fully tightened before use.

WARNING! Do not stand or sit on the table. It is designed for dining and general household use only.

Step-by-Step Assembly

Estimated assembly time: 30-45 minutes for two people.

1. Prepare the frame: Lay the support frame upside down on a protected surface.
2. Attach legs: Align each leg with the corner brackets on the frame. Insert and tighten the provided wood screws using a Phillips screwdriver.
3. Attach table top: Turn the frame right-side up. Place the table top upside down on a soft surface. Position the frame centrally on the underside of the top.
4. Insert dowels: Insert wooden dowels into the pre-drilled holes in the table top. Gently tap with a soft mallet if needed.
5. Secure with cam locks: Align the frame holes with the dowels. Insert the cam lock nuts into the frame and turn clockwise with the Allen key until tight. Do not overtighten.
6. Attach felt pads: Peel backing and stick one felt pad to the bottom of each leg.
7. Final check: Turn the table upright. Check all connections are secure and the table does not wobble.

Tip: If parts do not align easily, do not force them. Check orientation and hole alignment.

Adjustments & Leveling

If the table wobbles on an uneven floor:

1. Check that all legs are fully screwed in and cam locks are tight.
2. If wobble persists, adjust the height of individual legs using the adjustable glides (if your model includes them) by turning clockwise to raise or counterclockwise to lower.
3. Place a level on the table top to verify it is even.

Note: Some floor unevenness is normal; minor adjustments should stabilize the table.

Care & Maintenance

To keep your table looking its best:

• Cleaning: Wipe with a damp, soft cloth. For stubborn stains, use a mild soap solution. Dry immediately with a clean cloth.
• Protection: Use coasters, placemats, or a tablecloth to prevent heat marks, scratches, and water rings.
• Avoid: Harsh chemicals, abrasive cleaners, excessive moisture, and direct heat sources (e.g., hot pans directly on surface).
• Wood Care: The solid wood may expand/contract with humidity changes. Maintain consistent room humidity if possible.

CAUTION! Never use steel wool or scouring pads.

Weight Capacity & Usage

• Maximum Weight Capacity: 100 kg (220 lbs) evenly distributed.
• Intended Use: Dining, working, studying, and general household activities.
• Not Designed For: Standing, sitting, climbing, or as a workbench for heavy tools.
• Environment: For indoor use only. Not suitable for damp or outdoor areas.

WARNING! Exceeding the weight limit may cause damage or collapse, leading to injury.

Disassembly & Moving

To disassemble for moving or storage:

1. Clear the table surface.
2. Turn the table upside down on a protected surface.
3. Using the Allen key, turn the cam lock nuts counterclockwise to loosen and remove them.
4. Gently separate the frame from the table top.
5. Unscrew the legs from the frame if desired.
6. Store all hardware in a labeled bag taped to a large part.

Tip: Keep the assembly instructions and hardware for future reassembly.

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty leaflet included in the packaging or visit www.ikea.com for terms and conditions. The warranty covers material and manufacturing defects under normal household use. It does not cover damage from improper assembly, accidents, modification, or lack of care.

For warranty service, contact IKEA customer support with your proof of purchase (receipt) and product number (092.598.44).

Troubleshooting

Need Help? Visit the IKEA website (www.ikea.com) for assembly videos or contact customer support.