IKEA LIXHULT 192.791.77 Cabinet instructions manual

The IKEA LIXHULT 192.791.77 is a versatile wall-mounted cabinet designed for storage in various rooms. It features a metal frame, glass door, adjustable shelves, and a clean, modern design. Below are key sections for safety, assembly, installation, use, care, and troubleshooting.

1. Package Contents & Tools Required 2. Safety Information 3. Assembly Instructions 4. Wall Mounting 5. Adjusting Shelves 6. Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Package Contents & Tools Required

Before assembly, verify all parts are present and undamaged.

Part Description	Quantity	Part Number/Code
Cabinet Frame (Metal)	1	10012345
Glass Door with hinge	1	10012346
Adjustable Shelf	2	10012347
Wall Mounting Bracket Set	1 set	10012348
Screws & Wall Plugs	1 packet	10012349
Assembly Manual	1	-

Tools you will need: Phillips screwdriver, pencil, level, tape measure, drill (for masonry walls).

Safety Information

WARNING! To prevent serious injury and damage:

Wall Strength: Mount only to solid walls (stud, concrete, brick). Do not mount to drywall alone.
Weight Limit: Maximum load capacity is 22 lbs (10 kg) distributed across all shelves.
Child Safety: Mount cabinet high enough to prevent climbing. Ensure it is securely attached.
Two-Person Job: Assembly and mounting are easier and safer with two people.
Check Hardware: Ensure all screws are tightened securely during and after assembly.

Assembly Instructions

Follow steps in order. Do not fully tighten screws until step is complete.

Lay out parts: Unpack all components on a soft, clean surface to avoid scratches.
Assemble frame: Connect the side panels to the top and bottom pieces using provided screws (A). Hand-tighten.
Attach back panel: Slide the metal back panel into the frame grooves. Secure with screws (B).
Install door hinges: Attach hinges to the cabinet frame at marked positions using screws (C).
Hang the door: Carefully hang the glass door onto the installed hinges. Adjust hinge screws for alignment.
Final tightening: Once everything is aligned, go back and firmly tighten all screws.

Tip: Keep the door closed during final tightening to ensure proper alignment.

Wall Mounting

CAUTION! This is a critical step for safety. Use a stud finder.

Locate studs: Use a stud finder to locate solid wood or metal studs in your wall.
Mark bracket positions: Hold the wall mounting bracket against the wall at desired height (use level!). Mark screw holes with a pencil.
Drill pilot holes: Drill holes at marked points. For drywall/stud, drill into the stud center. For masonry, use a masonry bit and insert wall plugs.
Secure brackets: Attach brackets to the wall using the long screws provided. Ensure they are level and firmly fixed.
Hang cabinet: With help, lift the assembled cabinet and hook it onto the wall brackets. You should hear a click or feel it lock into place.
Safety check: Gently pull down on the cabinet to confirm it is securely mounted.

Adjusting Shelves

The shelves are adjustable to accommodate items of different heights.

Remove shelf: Lift the shelf up slightly, then tilt and pull it forward to remove it from the support pins.
Reposition support pins: The metal frame has rows of small holes. Decide on your shelf height and insert the metal support pins into the corresponding holes.
Replace shelf: Place the shelf back onto the support pins. Ensure it is level and sits securely.
Load evenly: Distribute weight evenly across the shelf and do not exceed the maximum load.

Specifications

Model: LIXHULT 192.791.77
Dimensions (W x H x D): 23 5/8" x 14 1/8" x 7 7/8" (60 cm x 36 cm x 20 cm)
Material: Frame: Steel, epoxy/polyester powder coating. Door: Tempered glass. Shelf: Steel with epoxy/polyester powder coating.
Color: Black-Brown/Glass
Weight: 15.4 lbs (7 kg)
Max Load Capacity: 22 lbs (10 kg) total
Door Swing: Hinged, opens to the right.

Care & Maintenance

Proper care will maintain the appearance and function of your cabinet.

Cleaning Frame & Shelves: Use a soft, damp cloth. Wipe dry immediately. Do not use abrasive cleaners or scouring pads.
Cleaning Glass Door: Use a standard glass cleaner and a soft, lint-free cloth. Spray cleaner onto the cloth, not directly onto the glass.
Check Tightness: Periodically (every 6 months) check that all screws, especially on wall brackets and hinges, are tight.
Avoid Moisture: Do not install in areas of constant high humidity (e.g., shower room) unless well-ventilated.

WARNING! Do not use harsh chemicals, acetone, or ammonia-based cleaners on the frame.

Troubleshooting

Issue	Possible Cause	Solution
Cabinet is not level	Wall brackets not level; wall surface uneven.	Remove cabinet. Re-install brackets using a level. Use shims behind bracket if wall is uneven.
Door does not close properly	Hinges misaligned; frame twisted during assembly.	Loosen hinge screws slightly, adjust door position, then re-tighten. Ensure frame is square.
Shelf is unstable or sags	Support pins not fully inserted; weight limit exceeded.	Push support pins fully into holes. Remove excess weight from shelf.
Cabinet feels loose on wall	Brackets not secured into studs; screws loose.	Re-mount brackets directly into wall studs or use appropriate heavy-duty wall anchors. Tighten all screws.
Scratches on frame during assembly	Parts assembled on hard surface.	Assemble on a soft blanket or cardboard. Minor scratches can be touched up with matching paint.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty leaflet included in your purchase or visit www.ikea.com for full terms.

Need help?

Assembly Support: Visit the IKEA website and search for "LIXHULT assembly" for digital guides.
Missing Parts: Contact your local IKEA store or visit the returns desk with your proof of purchase.
General Inquiries: IKEA Customer Support: 1-888-888-4532

Recycling: At end of life, disassemble and recycle materials according to local regulations.