IKEA LINDBYN 205.073.19 Mirror instructions manual

The IKEA LINDBYN 205.073.19 is a rectangular wall mirror designed for indoor use. It features a simple, clean frame and is intended to be mounted securely to a wall. Below are key sections for safety, features, parts included, installation, care, and warranty information.

1. Features at a Glance 2. Parts Included 3. Tools Required 4. Safety Instructions 5. Step-by-Step Installation 6. Mounting & Leveling 7. Care & Cleaning 8. Specifications 9. Troubleshooting 10. Warranty & Support

Features at a Glance

Key components: Rectangular mirror glass, pre-attached hanging hardware, wall mounting brackets, and necessary screws/plugs.

Feature	Description
Frame	Simple, clean design suitable for various interiors
Glass	Clear, high-quality mirror glass
Mounting System	Pre-attached hooks or brackets for secure wall mounting
Intended Use	Indoor wall mounting only
Weight Capacity	Designed to support its own weight when properly installed

Parts Included

Unpack and verify all parts before starting installation.

Mirror (1 piece)
Wall mounting brackets/hardware (set)
Screws and wall plugs (set)
Instruction manual (this document)

WARNING! Do not discard any parts until assembly is complete. Check for damaged components.

Tools Required

You will need the following tools (not included):

Phillips screwdriver
Drill with appropriate drill bit for your wall type (e.g., masonry, wood, drywall)
Pencil
Measuring tape
Level
Stud finder (recommended for secure mounting)

CAUTION! Use correct tools to avoid damaging the mirror or wall.

Safety Instructions

Read all instructions before assembly and installation.

This mirror is heavy. Use two people for handling and installation.
Ensure the wall structure is solid and can support the mirror's weight.
Mount the mirror securely to a wall stud or use appropriate wall anchors for your wall type.
Keep away from children during assembly.
Do not mount above beds, sofas, or other furniture where people may lean against it.
Do not use in humid areas (e.g., bathrooms) unless specified as suitable.

WARNING! Improper installation can cause the mirror to fall, resulting in injury or damage.

Step-by-Step Installation

Follow these steps carefully for secure mounting.

Plan the Location: Choose a suitable wall. Use a stud finder to locate wall studs for the most secure mount.
Mark the Wall: Hold the mirror (with help) against the wall at the desired height. Lightly mark the top corners with a pencil. Use a level to ensure marks are even.
Mark Mounting Points: Using the template (if provided) or the mirror itself, mark the exact spots where screws will go.
Drill Holes: Drill holes at marked points using the correct drill bit for your wall. Insert wall plugs if not mounting into a stud.
Attach Brackets: If using separate brackets, screw them securely into the wall at the drilled holes.
Hang the Mirror: With assistance, carefully lift the mirror and hook it onto the mounted brackets or screws. Ensure it is securely seated.
Final Check: Gently test the mirror's stability. Use the level again to ensure it is straight.

Mounting & Leveling

Proper leveling is crucial for appearance and safety.

Tip: Use a long level across the top edge of the mirror for accuracy. Adjust before fully tightening all screws if your mounting system allows.

If the mirror is not level, carefully lift it off the mounts, adjust the wall hardware, and rehang.

WARNING! Do not overtighten screws into the mirror frame, as this may crack the glass or damage the frame.

Care & Cleaning

To maintain the mirror's appearance and longevity.

Unplug any nearby electrical items before cleaning if using liquid cleaners.
Use a soft, lint-free cloth (microfiber recommended).
For cleaning, use a mild glass cleaner or a solution of vinegar and water. Spray onto the cloth, not directly onto the mirror.
Wipe gently in a circular motion.
Dry with a separate clean, dry cloth to prevent streaks.

CAUTION! Do not use abrasive cleaners, scouring pads, or ammonia-based products on the frame. Avoid excessive moisture.

Specifications

Article Number: 205.073.19
Product Name: LINDBYN
Type: Wall Mirror
Dimensions (approx.): [Width] x [Height] x [Depth] cm/inches (Refer to product packaging)
Weight (approx.): [Weight] kg/lbs (Refer to product packaging)
Frame Material: [e.g., Particleboard, Fiberboard, Plastic]
Glass Type: Clear mirror glass
Country of Origin: To be marked on product label

Troubleshooting

Symptom	Possible Cause	Corrective Action
Mirror is not level	Wall mounts uneven or marking error	Remove mirror. Check wall mount height with level. Reinstall.
Mirror feels loose	Insufficiently tightened screws or incorrect wall plugs	Ensure screws are tight and anchored in a stud or appropriate wall plug for your wall type.
Frame damage out of box	Transport damage	Contact IKEA customer service with your receipt for parts or replacement.
Glass is blurry or has dark spots	Manufacturing defect or silvering damage	Do not install. Contact IKEA customer service for a replacement.
Cannot find wall studs	Stud finder error or unusual wall construction	Use heavy-duty toggle bolts or anchors rated for the mirror's weight in drywall. Consult a professional if unsure.

Warranty & Support

IKEA products come with a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for specific terms and duration.

For missing parts, assembly questions, or warranty claims:

Visit the IKEA website: www.ikea.com
Contact your local IKEA store.
Use the IKEA customer service hotline for your country.

Safety Notice: Always follow local building codes and regulations when mounting heavy items to walls. IKEA is not liable for improper installation or installation on insufficient walls.