IKEA LANGUR 103.592.63 Seat Shell instructions manual

The IKEA LANGUR 103.592.63 is a seat shell designed for use with compatible IKEA chair frames. It features a curved ergonomic design for comfort, is made from durable molded material, and includes pre-drilled mounting holes for easy assembly. Below are key sections for safety, parts identification, assembly instructions, installation, care, and warranty information.

1. Parts & Tools Included 2. Safety Information 3. Assembly Instructions 4. Installation to Frame 5. Weight & Dimensions 6. Care & Maintenance 7. Warranty & Support 8. Troubleshooting

Parts & Tools Included

Key components: Seat Shell (1 piece), Mounting Hardware Pack, Instruction Manual.

Part NumberDescriptionQuantity
103.592.63LANGUR Seat Shell1
114398Mounting Screws (M6 x 25mm)4
—Hex Key (4mm)1
—Instruction Manual1

Safety Information

Read all instructions before assembly and use.

  1. Inspect all parts for damage before assembly. Do not use damaged parts.
  2. Ensure the compatible chair frame is stable and on a level surface before attaching the shell.
  3. Use only the provided hardware. Do not overtighten screws.
  4. Maximum user weight: 110 kg (242 lbs). Do not exceed this limit.

WARNING! Improper assembly can result in injury or damage. Assemble on a soft surface to avoid scratching the shell.

Assembly Instructions

Follow these steps to prepare the seat shell for installation.

  1. Unpack: Remove all packaging materials and lay the seat shell upside down on a clean, soft surface (e.g., a towel or carpet).
  2. Identify mounting points: Locate the four pre-drilled holes on the underside of the shell.
  3. Prepare hardware: Have the four mounting screws and the hex key ready.
  4. Align with frame: Proceed to the installation section.

CAUTION! Do not force the shell during alignment. The holes should align easily with the frame brackets.

Installation to Frame

Attaching the seat shell to a compatible IKEA chair frame (e.g., LANGUR base frame).

  1. Position the chair frame upright.
  2. Place the seat shell onto the frame's mounting brackets, ensuring all four holes align.
  3. Insert one screw into each hole by hand to start.
  4. Using the provided hex key, tighten all four screws firmly in a cross pattern (e.g., top-left, bottom-right, top-right, bottom-left). Do not overtighten.
  5. Check stability: Gently rock the seat to ensure it is securely attached with no movement.

Tip: For two-person assembly, one person can hold the shell in place while the other tightens the screws.

Weight & Dimensions

Care & Maintenance

Clean with a damp cloth and mild detergent. Do not use abrasive cleaners or solvents.

CAUTION! Do not expose to direct heat sources (e.g., radiators, fireplaces) or leave in direct sunlight for extended periods, as this may cause warping or color fading.

Warranty & Support

This product is covered by IKEA's limited warranty. Refer to the IKEA warranty document included with your purchase or available at www.ikea.com.

For assembly support, missing parts, or product questions:

Troubleshooting

SymptomPossible CauseCorrective Action
Seat shell does not align with frame holesWrong frame model; shell rotated incorrectlyVerify frame compatibility. Rotate the shell 180 degrees and try again.
Seat feels loose or wobbly after installationScrews not fully tightened; frame brackets damagedTighten all screws firmly in a cross pattern. Inspect frame brackets for damage.
Cracks or damage on the shellShipping damage; over-tightening; excess weightDo not use a damaged shell. Contact IKEA for a replacement part.
Screws are missing or do not fitHardware pack incomplete or incorrectUse only the provided M6 x 25mm screws. Contact IKEA for missing hardware.

Note: This seat shell is a component. Ensure the complete chair assembly (frame, shell, legs) is stable before use.

IKEA LANGUR 103.592.63 Seat Shell instructions manual © - All Rights Reserved 2025