IKEA LACK 602.821.86 Wall Shelf instructions manual

The IKEA LACK 602.821.86 is a versatile and modern wall shelf designed for easy installation and efficient space utilization. This manual provides essential information for safe assembly, mounting, usage, and care of your LACK wall shelf. Below are key sections covering parts identification, safety warnings, step-by-step assembly, mounting instructions, weight limits, and maintenance.

1. Parts & Components 2. Safety Information 3. Tools Required 4. Step-by-Step Assembly 5. Wall Mounting Instructions 6. Weight Capacity & Usage 7. Care & Cleaning 8. Troubleshooting 9. Warranty & Support

Parts & Components

Ensure all parts are present before starting assembly. Key components include the shelf board, wall brackets, screws, wall plugs, and assembly hardware.

Part Name	Quantity	Description
Shelf board	1	Main shelf surface, laminated particleboard
Wall bracket	2	Metal brackets for wall attachment
Screw	4	For securing brackets to wall
Wall plug	4	Anchors for solid wall mounting
Assembly screw	4	For attaching shelf to brackets
Allen key	1	Included tool for assembly

Safety Information

Read all instructions before assembly. Ensure safe handling and installation.

Use two people for assembly and mounting to prevent injury.
Mount only on solid walls (concrete, brick, studs). Do not mount on plasterboard alone.
Keep children and pets away during assembly.
Use appropriate personal protective equipment if drilling.

WARNING! Incorrect mounting can cause the shelf to fall, resulting in injury or damage. Always use suitable wall anchors and verify wall type.

Tools Required

In addition to the included Allen key, you will need:

Drill: For making pilot holes in wall.
Hammer: For inserting wall plugs.
Screwdriver: Phillips head for screws.
Level: To ensure shelf is mounted horizontally.
Pencil: For marking drill points.
Tape measure: For accurate placement.

Step-by-Step Assembly

Follow these steps in order. Do not fully tighten screws until all parts are aligned.

Identify the two wall brackets and the shelf board.
Place the shelf board upside down on a soft, protected surface.
Position a wall bracket at each end of the shelf, aligning the holes.
Insert the assembly screws through the bracket holes into the shelf.
Hand-tighten with the Allen key, but do not fully tighten yet.
Check alignment, then fully tighten all screws securely.

CAUTION! Avoid overtightening screws, as this may damage the shelf material.

Wall Mounting Instructions

Mounting requires careful measurement and drilling into a solid wall.

Decide on the shelf height and location. Ensure no pipes or wires are behind the wall.
Hold the assembled shelf against the wall in the desired position.
Use a level to ensure it is perfectly horizontal. Mark the bracket screw holes with a pencil.
Set the shelf aside. Drill pilot holes at the marked points using a drill bit suitable for your wall plugs.
Insert the wall plugs into the holes using a hammer.
Hold the shelf back in position, aligning brackets with the holes.
Insert the mounting screws through the brackets into the wall plugs.
Tighten the screws firmly with a screwdriver until the shelf is secure and does not move.

Tip: For stud walls, locate and drill directly into wooden studs for maximum strength.

Weight Capacity & Usage

Adhere to weight limits to ensure safety and product longevity.

Max. Load Capacity: 11 lbs (5 kg) evenly distributed.
Recommended Items: Books, decorative objects, small plants, photo frames.
Not Recommended: Heavy electronics, large appliances, liquids in open containers.
Placement: Do not place near heat sources or in areas of high humidity.

WARNING! Exceeding the weight limit can cause the shelf to detach from the wall or the board to sag or break.

Care & Cleaning

Proper care will maintain the appearance and function of your shelf.

Unload the shelf before cleaning or attempting to adjust.
Use a soft, slightly damp cloth to wipe the surface. Wipe dry immediately.
For stubborn marks, use a mild soap solution. Do not use abrasive cleaners, scouring pads, or solvents.
Avoid prolonged exposure to direct sunlight to prevent fading.

CAUTION! Never soak the shelf or allow liquid to seep into the edges, as this can cause the particleboard to swell.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Shelf is not level	Uneven wall or incorrect marking	Remove shelf, re-measure and re-drill holes using a level.
Shelf feels loose	Screws not tight or wrong wall plugs	Tighten all screws. If in drywall, ensure anchors are designed for the weight.
Brackets not aligning	Assembly screws not properly started	Loosen screws, realign bracket holes with shelf, then retighten.
Damage to shelf surface	Overtightening or impact	Minor scratches can be touched up with a matching furniture marker.
Cannot insert wall plugs	Hole too small or debris inside	Re-drill hole to correct size and clean out dust.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for full terms and conditions.

Customer Support: For missing parts, assembly questions, or other support, visit the IKEA website at www.ikea.com or contact your local IKEA store.

Recycling: At the end of its life, disassemble and recycle materials according to your local regulations.